EDU-TOYS CIRCUIT MAKER Skill Builder 125 Скачать руководство пользователя страница 13

Страница: 13 / 64

Project #3

Super Circuit

Placement

Level

Numbers

This complex circuit is pictured

on the box cover. Use that as a

guide to help in building it.

WARNING:

Moving parts. Do not touch the

fan or motor during operation. Do not lean

over the motor.

WARNING:

Fan may not rise until switch is

released.

Circuit Maker Skill Builder 125 uses electronic

blocks that snap onto a clear plastic grid to

build different circuits. These blocks have

different colors and numbers on them so that

you can easily identify them.
Build the circuit shown above by placing all the

parts with a black

next to them on the board

first. Then, assemble parts marked with a

Then, assemble parts marked with a

. Then,

assemble the part marked with a

(the alarm

IC (U2), which should be placed directly over

the music IC (U1)). Install two (2) “AA” batteries

(not included) into the battery holder (B1).

Place the glow fan on the motor (M1).
Turn on the slide switch (S1). You hear music

and alarm sounds, and the red LED (D1) lights.

The lamp (L1) may light briefly before the red

LED turns on. Cover the photoresistor (RP) to

change the sound a little.
Push the press switch (S2) to spin the motor

and glow fan. Release the press switch when

the motor is spinning at full speed. The glow fan

should float through the air like a flying saucer.

Be careful not to look directly down on the glow

fan when it is spinning.

If the fan doesn’t fly off, then push and release

the press switch several times rapidly when it is

at full speed.
If the 470

F capacitor (C5) is discharged when

you turn on the slide switch, then the lamp will

light for a few seconds as the circuit charges up

C5. L1 will not light again until C5 is

discharged. To discharge C5, remove it from

the circuit and place it directly on the 4-snap

wire for an instant, then move it back to its

normal spot in the circuit.

-12-

Placement Level Numbers

CM-125_Manual_031514.qxp_CM-125_Manual_031514 4/2/14 12:19 PM Page 13

Содержание CIRCUIT MAKER Skill Builder 125

































































Результаты поиска

Содержание CIRCUIT MAKER Skill Builder 125

Отзывы:

Бренды по названию

Популярные бренды

EDU-TOYS CIRCUIT MAKER Skill Builder 125, Инструкция по эксплуатации

Результаты поиска

Содержание CIRCUIT MAKER Skill Builder 125

Отзывы:

Бренды по названию

Популярные бренды