EDU-TOYS CIRCUIT MAKER Skill Builder 125 Скачать руководство пользователя страница 5

Страница: 5 / 64

-4-

About Your Circuit Maker Skill Builder 125 Parts

(Part designs are subject to change without

notice).

BASE GRID

BATTERY HOLDER

The

base grid

is a platform for mounting parts

and wires. It functions like the printed circuit

boards used in most electronic products, or like

how the walls are used for mounting the

electrical wiring in your home.

SNAP WIRES

The

batteries (B1)

produce an electrical voltage

using a chemical reaction. This “voltage” can be

thought of as electrical pressure, pushing

electricity through a circuit just like a pump

pushes water through pipes. This voltage is

much lower and much safer than that used in

your house wiring. Using more batteries

increases the “pressure”, therefore, more

electricity flows.

Battery Holder (B1)

SLIDE & PRESS SWITCHES

The

slide & press switches (S1 & S2)

connect

(pressed or “ON”) or disconnect (not pressed or

“OFF”) the wires in a circuit. When ON they

have no effect on circuit performance. Switches

turn on electricity just like a faucet turns on

water from a pipe.

Slide & Press

Switches

(S1 & S2)

RESISTORS

The

photoresistor (RP)

is a light-sensitive

resistor, its value changes from nearly infinite in

total darkness to about 1,000

when a bright

light shines on it.

Photoresistor (RP)

LAMP

CAPACITOR

The

470

F capacitor (C5)

can store electrical

pressure (voltage) for a period of time. This

storage ability allows it to block stable voltage

signals and pass changing ones. Capacitors are

used for filtering and delay circuits.

A light bulb, such as in the

2.5V lamp (L1)

contains a special thin high-resistance wire.

When a lot of electricity flows through, this wire

gets so hot it glows bright. Voltages above the

bulb’s rating can burn out the wire.

Lamp (L1)

Resistors “resist” the flow of electricity and are

used to control or limit the current in a circuit.

Circuit Maker Skill Builder 125 includes

100

(R1) and 1K

(R2) resistors

(“K” symbolizes

1,000, so R2 is really 1,000

). Materials like

metal have very low resistance (<1

), while

materials like paper, plastic, and air have near-

infinite resistance. Increasing circuit resistance

reduces the flow of electricity.

Resistors (R1 & R2)

Capacitor (C5)

The blue

snap wires

are wires used to

connect components.

They are used to transport

electricity and do not affect

circuit performance. They come in

different lengths to allow orderly

arrangement of connections on the base grid.

CM-125_Manual_031514.qxp_CM-125_Manual_031514 4/2/14 2:51 PM Page 5

Содержание CIRCUIT MAKER Skill Builder 125

































































Результаты поиска

Содержание CIRCUIT MAKER Skill Builder 125

Отзывы:

Бренды по названию

Популярные бренды

EDU-TOYS CIRCUIT MAKER Skill Builder 125, Инструкция по эксплуатации

Результаты поиска

Содержание CIRCUIT MAKER Skill Builder 125

Отзывы:

Бренды по названию

Популярные бренды