Edge Electrons EDGEIQ EE-202-0050 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 32

Edge Electrons EDGEIQ EE-202-0050 Скачать руководство пользователя страница 6

4

E D G E I Q H A N D B O O K

1.4. Wiring

1.4.1. Single phase, two phase and three phase installation

This

single phase EdgeIQ unit

MUST be installed according to the

type of supply

available on

the installation and whether a single phase solar inverter or single phase battery inverter is part of

the installation or not.

This manual provides specific wiring instructions for installations that have a

single phase supply

only.

Note: If your installation has

a two phase supply, three phase supply or battery inverter

, we

recommend you contact your Edge Electrons representative to discuss alternatives.

1.4.2. Termination to the unit internal breaker rating

1.4.3.

WARNING

:

Do

NOT

install EdgeIQ on installations

with

three phase

OR

two phase

supply

as this can

UNBALANCE

the voltages and cause damage to the installation or appliances on the installation.

Three

phase

Edge IQ is available with a 3 phase adaptor, please contact

[email protected]

for further support.

«
...
4
5
6
7
8
...
»

Содержание EDGEIQ EE-202-0050

































Отзывы:

Нет отзывов