manualshive.com logo in svg

Edge Electrons EDGEIQ EE-202-0050, Инструкция по установке, пуско-наладке и эксплуатации, Страница: 30 / 32

Поделиться
Скачать
Edge Electrons EDGEIQ EE-202-0050 Скачать руководство пользователя страница 30

 

28    

 

E D G E I Q    H A N D B O O K

 

9.

 

A P P E N D I X   C :  E D G E   I Q   L E D    S T A T U S    I N D I C A T O R S   

 

LED Status Indicators 

 

LED Response 

EdgeIQ Status 

Steady Green 

EdgeIQ is online and is in regulation mode 

Flashing Green 

EdgeIQ is offline and is in regulation mode 

Steady Red 

EdgeIQ is online and is in bypass mode due to enable force bypass 

command. Please contact [email protected] 

Flashing Red 

EdgeIQ is offline and is in bypass mode due to enable force bypass 

command. Please contact [email protected] 

2s Steady Green, 2s Steady 

Orange 

EdgeIQ is online and is in bypass mode due to faults caused by 

external factors such as input voltage, output load, and ambient 

temperature. LED should go back to solid green in sometime  

2s Flashing Green, 2s 

Flashing Orange 

EdgeIQ is offline and is in bypass mode due to faults caused by 

external factors such as input voltage, output load, and ambient 

temperature. LED should go back to solid green in sometime 

2s Steady Red, 2s Steady 

Orange 

EdgeIQ is online and is in bypass mode due to faults caused by 

internal factors such as auxiliary supply voltage and hotspot 

temperature. LED should go back to solid green in sometime 

2s Flashing Red, 2s Flashing 

Orange 

EdgeIQ is offline and is in bypass mode due to faults caused by 

internal factors such as auxiliary supply voltage and hotspot 

temperature. LED should go back to solid green in sometime 

2s Steady Red, 2s Steady 

Green 

EdgeIQ is online and is in bypass mode due to faults that suggest 

possible hardware failure. Please contact 

[email protected] 

2s Flashing Red, 2s Flashing 

Green 

EdgeIQ is offline and is in bypass mode due to faults that suggest 

possible hardware failure. Please contact 

[email protected] 

Steady Orange 

EdgeIQ is offline and the comms module application is not working. 

Please contact [email protected] 

 

 

COMMISIONING COMPLETE 

 

 

 

 

 

 

 

 

 

 

 

 

***End*** 

 

 

 

 

Содержание EDGEIQ EE-202-0050

































Отзывы:

Нет отзывов