Edge-Core ES3526VA-PoE Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 74

Edge-Core ES3526VA-PoE Скачать руководство пользователя страница 61

Fiber Standards

B-5

B

Adjusting Existing Category 5 Cabling to Run 1000BASE-T

If your existing Category 5 installation does not meet one of the test parameters for
1000BASE-T, there are basically three measures that can be applied to try to correct
the problem:

1.

Replace any Category 5 patch cables with high-performance Category 5e or
Category 6 cables.

2.

Reduce the number of connectors used in the link.

3.

Reconnect some of the connectors in the link.

Fiber Standards

The current TIA (Telecommunications Industry Association) 568-A specification on
optical fiber cabling consists of one recognized cable type for horizontal subsystems
and two cable types for backbone subsystems

.

Horizontal

62.5/125 micron multimode (two fibers per outlet).

Backbone

62.5/125 micron multimode or single-mode.

TIA 568-B will allow the use of 50/125 micron multimode optical fiber in both the
horizontal and backbone in addition to the types listed above. All optical fiber
components and installation practices must meet applicable building and safety codes.

«
...
59
60
61
62
63
...
»

Содержание ES3526VA-PoE











































































Отзывы:

Нет отзывов