Edge-Core ES3526VA-PoE Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 74

Edge-Core ES3526VA-PoE Скачать руководство пользователя страница 39

Installing an SFP Transceiver

3-7

3

Installing an SFP Transceiver

Figure 3-5 Installing an SFP Transceiver

The SFP slots support the following optional SFP transceivers:

• 100BASE-FX
• 1000BASE-SX
• 1000BASE-LX
• 1000BASE-LH

To install an SFP transceiver, perform the following steps:

1.

Consider your network and cabling requirements to select an appropriate SFP
transceiver type.

2.

Insert the transceiver with the optical connector facing outward and the slot
connector facing down. Note that SFP transceivers are keyed so they can only be
installed in one orientation.

3.

Slide the SFP transceiver into the slot until it clicks into place.

Note:

SFP transceivers are hot-swappable. The switch does not need to be powered off
before installing or removing a transceiver. However, always first disconnect the
network cable before removing a transceiver.

Note:

SFP transceivers are not provided in the switch package.

22

23

24

23

24

ES3526V

A-PoE

Link/A

ct

PoE

25

26

Pwr

Diag

Stack

Mode

PoE

/Link

RPS

«
...
37
38
39
40
41
...
»

Содержание ES3526VA-PoE











































































Отзывы:

Нет отзывов