background image

Catalog #70080, #70081, #70082, #70083
Brochure No. 63-0312

©2008 Edelbrock Corporation

Rev. 07/08

Page 10

2.0

Performer RPM II Nitrous System Installation

2.1

Nitrous Bottle Mounting

The nitrous oxide storage cylinder is typically called a “nitrous bottle”. It is an aluminum cylinder, designed and
manufactured to withstand very high pressures. The valve on top of the bottle is a high-flow design that allows easy
opening and closing which controls the nitrous flow to the engine compartment.

Accurate calibration of your nitrous system depends on the bottle remaining at a stable temperature. In vehicles (such as
Corvettes) where the bottle must be mounted in an area subject to direct sunlight, it is suggested that the bottle be
shielded with a bottle blanket.

If the bottle is mounted inside the passenger compartment or in a space that has access to the passenger compartment
such as hatchbacks or vehicles that feature fold down rear seats, the pressure relief device (PRD valve) must be vented
externally from the cockpit. This procedure will prevent the passenger compartment from filling with a cloud of nitrous
oxide, should the safety pressure relief valve rupture. For more information, please contact our Technical Department.

Special consideration should be made to protect the bottle installation by not placing the bottle in
a known crumple or crash zone within the vehicle. At no time should the bottle be mounted within
the seating area of the passenger compartment of a street-driven vehicle.

Here is the Performer Bottle Valve. Installed on all bottle valves used in Edelbrock Nitrous Systems,
is a Pressure Relief Device or “PRD”. It is a safety valve designed to vent the contents of the bottle
into the atmosphere in case of a catastrophic event like a collision. It is also installed to prevent
the over-pressurization of the bottle. Unsafe bottle pressure is caused by over filling or elevated
bottle temperatures.

There are two types of PRDs. Internal piping and external piping. Internal requires no additional
parts. The external type requires a safety blowdown tube designed to route the gas, if the PRD
happens to rupture to the outside of vehicle. The internal type is design to vent directly off the
bottle into the atmosphere.

It is illegal to tamper with or remove this device.

Bottle Safety Information

1.

D

Do

o  n

no

ott

attempt to remove the bottle valve. Please return your bottle to Edelbrock if service is required to

the siphon tube inside the bottle or the bottle valve itself.

2.

Never

heat the outside of your nitrous bottle with an open flame like that of a torch.

3.

Do not

strike the surface of your nitrous bottle with a heavy or sharp object.

4.

Do not

drop your nitrous bottle.

5.

Do not

attempt to grind off or destroy any imprinted markings on the face of the bottle.

6.

Do not

remove, modify or otherwise tamper with the safety valve on the bottle valve.

7.

Do not 

attempt to use a bottle that has been damaged or tampered with.

Racing Vehicles

Before you mount a nitrous bottle in a vehicle intended for use in racing or sanctioned events, check with the sanctioning
association or local racetrack for any rules regarding bottle installation. Most associations require the bottle be mounted
within the confines of the safety roll cage, with the safety pressure relief cap vented away from the driver’s compartment.

660 High
Flow Nitrous
Exit

Pressure

Relief Device

(PRD)

Содержание 70080
































Отзывы: