background image

Catalog #70080, #70081, #70082, #70083
Brochure No. 63-0312

©2008 Edelbrock Corporation

Rev. 07/08

Page 6

1.2

Jet Map Information

Edelbrock engineering has conducted dyno testing with the Performer RPM II system to provide you with a baseline jet
map. These jet combinations are supplied with this system to enable you to vary your engine’s power output. On a typical
mildly to highly modified 350 or larger cubic inch engine, you can expect the following approximate power gains for each
of the jetting levels:

Performer RPM II Jet Map

2-Stage Performer RPM II Jet Map

JET MAP NOTES:
Pressures:

Maintain 6.5 psi fuel pressure and 950 psi nitrous oxide bottle pressure for safe and effective operation.

Spark Plugs:

Two heat ranges colder than an equivalent naturally aspirated engine would use.

Fuel:

110 octane or higher race gas is required to prevent detonation.

The dyno tests were conducted at Edelbrock using a highly modified Big Block Chevrolet. Modifications included Edelbrock
intake manifold, cylinder heads dyno headers, pistons, rods, crankshaft, and improved ignition. All stated timing
adjustments listed in the jet map are where the motor being tested performed best. Final timing should be adjusted to
achieve best power and/or MPH per application.

See section “5.0 Ignition Timing and Nitrous” for more information on

timing selection.

Any variations in jetting patterns other than what is listed above and engine damage could occur. Please contact Edelbrock
Technical Department with any questions you have concerning jetting patterns and their effects on engine performance.

Edelbrock recommends an NGK spark plug with a heat range between -9 and -11, depending on the power level being
used. When in doubt, always go to the next cooler heat range.

The Performer RPM II Series Nitrous Systems are intended for single-plane manifolds only.  Do not use a
dual-plane manifold with the Performer RPM II Series Nitrous Systems.

In testing, we found that dual-plane

manifolds have some distribution problems at these super high flow rates that could cause serious engine damage.

Approximate HP Gain

Nitrous Jet

Fuel Jet

Timing Adjustment

200

85

85

7°-9° retard

225

93

93

8°-10° retard

300

102

102

11°-13° retard

400

116

116

15°-17° retard

1st Stage Jet and Timing Map

2nd Stage Jet Map

Dual Stage Timing Map

Initial HP

Gain

Nitrous

Jet

Fuel

Jet

1st Stage Timing

Adjustment

Additional

HP Gain

Nitrous Jet Fuel Jet Total HP Gain Total Timing Adjustment

100

59

59

3°-5° retard

100

59

59

200

7°-9° retard

150

71

71

5°-7° retard

150

71

71

300

11°-13° retard

200

85

85

7°-9° retard

200

85

85

400

15°-17° retard

Содержание 70080
































Отзывы: