Eddyfi Technologies INUKTUN VERSATRAX 300 Скачать руководство пользователя страница 21

Страница: 21 / 67

Versatrax 300™

Document: UMBH008532.docm

Revision: A07

Created by: KJB

Date: 26 Sep 2019

3047763-A07

Source Location: C:\ePDM\ISLEng\products\bh-vt300series4-trackchassis\manuals\UMBH008532.docm

Page 21 of 67

Versat

rax 30

0 User Ma

For IB

5954

FIGURE 9: LIGHT INSTALLATION & ADJUSTMENT

Rear Camera Installation

The Versatrax 300

™ system can accept one auxiliary 72V Crystal Cam® camera, which is designated as

the rear facing camera for tether observation. As illustrated below, the mounting bracket is located on the
back of the tether termination can.

Warning:

The plug-in whip is supplied with 48 VDC. This whip must be capped with a dummy

plug whenever the Crystal Cam® is removed. Electric shock or system damage may otherwise

result. Never operate the system with this connector open.

Warning:

The Versatrax Crystal Cam is different from a standard Crystal Cam. It uses a higher

voltage and different connector than the standard Crystal Cam (eight and six-pin, respectively).

You cannot use a standard Crystal Cam® with the Versatrax system. Attempts to install the

standard Crystal Cam® will

destroy

the camera.

Installation:

1.  Remove the cable clamp holding the camera whip.
2.  Install the camera bracket as shown using two #10-24 x ½in pan head screws.
3.  Install the camera using two #6-32 x ¾in pan head screws. Note the camera orientation marked

“TOP” seen on the label inside the epoxy.

4. Apply a small amount of silicone grease to the camera connector pins.
5. Secure the locking collar after plugging in the camera.

Содержание INUKTUN VERSATRAX 300




































































Результаты поиска

Содержание INUKTUN VERSATRAX 300

Отзывы:

Похожие инструкции для INUKTUN VERSATRAX 300

Бренды по названию

Популярные бренды

Eddyfi Technologies INUKTUN VERSATRAX 300, Руководство пользователя

Результаты поиска

Содержание INUKTUN VERSATRAX 300

Отзывы:

Похожие инструкции для INUKTUN VERSATRAX 300

Бренды по названию

Популярные бренды