background image

11

REV. 03/2015

3. The vehicle can lift but cannot retain, by turn-
    ing the handle, the vehicle can lift, or although 
   the vehicle can lift, but then automatically 
    lower?

Cause 1 Valve blocked by debris.

Troubleshooting:

Remove all the parts within the valve, 
clean them up and re-install, the fault can 
then be fi xed.
Seals need to be replaced when necess-
ary.

1. Valves are precision parts, apart from 
the seals, no parts shall be replaced or 
swapped between two vehicles, otherwise 
may need a technician with certain skills to 
fi x!
2. An appropriate amount of hydraulic oil 
needs to be refi lled depending on the loss 
of hydraulic oil! Warning! DO NOT attempt 
this repair operation without proper 
training!

4. The vehicle can lift but cannot lower?

Cause 1

Piston rod bent or bonded with cylinder 
block.

Cause 2

May be caused by other parts on the 
vehicle.

Cause 3

May be caused by the vehicle getting rusty 
or blocked by foreign bodies.

Troubleshooting:

Check all the related parts of the entire 
vehicle for abnormalities, remove the 
foreign objects on other parts, rectify and 
replace the damaged or deformed parts.

5. The vehicle cannot lower to bottom?

Cause 1 Excessive hydraulic oil.

Troubleshooting:

Drain the excessive hydraulic oil.

HYDRAULIC SYSTEM

Содержание EPT20-15EHJ






























Отзывы: