ECS P6LX2-A Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 84

ECS P6LX2-A Скачать руководство пользователя страница 78

P6LX2-A User’s Manual

4:

Reference Information – 4.36

IDE HDD Block Mode

Enables hard disk drive block transfer mode . The setting op-

tions are:

Enabled (default)

Disabled

On-Chip Primary/Secondary PCI IDE

Enables or Disables the Primary or Secondary PCI controllers.

Selecting “Disabled” releases IRQ14 ( for Primary) or IRQ15 (for
Secondary).

Enabled (default)

Disabled

IDE Primary/Secondary Master/ Slave PIO

These four lines set the hard disk PIO transfer mode, which

affects the hard disk data transfer rate. The system will auto-
detect the PIO mode of a device in any of these positions when
they are set to ‘Auto’, the recommended setting. Alternatively,
you can set the mode manually. Modes 0 to 4 are supported.

Ultra DMA/33 Support

The default setting, Enabled, enables hard disk UltraDMA

transfer mode, which requires a drive that supports this data trans-
fer method. The system will auto-detect an UltraDMA device in
any of the four IDE positions. The other setting is ‘Disabled’.
You can leave this set to Auto without effect if there are no
UltraDMA devices installed.

USB Keyboard Support

Enables or Disables support for a USB keyboard. Enable this if

you connect a USB keyboard. The default is Disabled.

«
...
76
77
78
79
80
...
»

Содержание P6LX2-A





















































































Отзывы:

Нет отзывов