ECS Mantis PV-28SV50-BN-1 Скачать руководство пользователя

Страница: 31 / 56

22618-12-0707

Page 31

DIRECT VENT INSTALLATION INSTRUCTIONS (cont.)

EXTERIOR GRADE

FLUE CENTER

1 1/4”

(3.2cm)

MIN.

12”

(30.5cm)

MIN.

FLOOR PROTECTION

FLOOR PROTECTION
NO HEARTH REQUIRED

EXTERIOR GRADE

FLUE CENTER

1 1/4”

(3.2cm)

MIN.

12”

(30.5cm)

MIN.

Figure 36

Minimum Exterior Grade Dimension - Unit Without Pedestal

Figure 37

Minimum Exterior Grade Dimension - Unit With Pedestal

Installation on Rugs and Tile

If this appliance is to be installed directly on

carpeting, tile, or other combustible mate-

rial, other than wood ﬂooring, the appliance

shall be installed on a metal or wood panel

extending the full width and depth of the

appliance.
The base referred to above does not mean

the ﬁre-proof base as used on wood stoves.

The protection is primarily for rugs that may

be extremely thick and light-color tile that

can discolor.

EXTERIOR GRADE

FLUE CENTER

12”

(30.5cm)

MIN.

Figure 38

Minimum Exterior Grade Dimension - Existing Fireplace Installation

Содержание Mantis PV-28SV50-BN-1

























































Результаты поиска

Содержание Mantis PV-28SV50-BN-1

Отзывы:

Похожие инструкции для Mantis PV-28SV50-BN-1

Бренды по названию

Популярные бренды

ECS Mantis PV-28SV50-BN-1, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание Mantis PV-28SV50-BN-1

Отзывы:

Похожие инструкции для Mantis PV-28SV50-BN-1

Бренды по названию

Популярные бренды