Masport BALTIMORE ACC LP Owner'S Installation Manual Download | Manualshive

Page: 1 / 20

background image

Owners &

Installation

Manual

Baltimore
Gas Fires

PLEASE KEEP THESE INSTRUCTIONS
FOR FUTURE REFERENCE

WARNING

Improper installation, adjustment, alteration,
service or maintenance can cause injury or
property damage.
For assistance or additional information
consult an authorized technichian, or your
Masport Gas Fire Dealer.

FOR YOUR SAFETY

Do not store or use gasoline or other
flammable vapours and liquids in the vicinity
of this appliance

Installation and service must be performed by
authorized personnel.

FOR YOUR SAFETY

What to do if you smell gas

Do not try to light any
appliance
Do not touch any
electrical switch
Do not use any phone
in your building
Immediately close the
shutoff valve behind the
heater
Call the technician

•
•
•
•

•

Metal Fab Industies Limited - New Zealand
PO Box 58 473
Greenmount
Auckland

Metal Fab PTY - Australia
Unit 2, 205 Abbotts Road
Dendenong South
Victoria 3175

591363

1
2
3
...
»

Summary of Contents for BALTIMORE ACC LP





















Reviews:

No comments

Related manuals for BALTIMORE ACC LP

Brand: Majestic fireplaces Pages: 28

Brand: Majestic fireplaces Pages: 52

Brand: Majestic fireplaces Pages: 4

Brand: Majestic fireplaces Pages: 24

Brand: Majestic Pages: 64

Royal Collection WMC36

Brand: Majestic fireplaces Pages: 8

PerfectView 33LDV

Brand: Majestic fireplaces Pages: 4

Brand: M Design Pages: 44

Brand: ELEMENTI Pages: 60

Brand: SEI Pages: 8

Brand: HAMPTON BAY Pages: 7

Brand: Jetmaster Pages: 32

Brand: Somogyi Elektronic Pages: 35

Fireplace Glass Door

Brand: pleasant hearth Pages: 27

Brand: Dimplex Pages: 20

Brand: HEINZE Pages: 2

Brand: Febo Pages: 16

Brand: Febo Flame Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands