ECR International Ductless Series Скачать руководство пользователя

Страница: 19 / 40

PN 20009722 REV E, [02/11/2015]

THERMOSTAT OPERATION

CAW Wall Mounted Thermostat Operation
Thermostat Selection

• Choose 24Vac, dry contact type thermostat that

matches your application.

• EMI equipment is compatible with most standard

bimetal, mercury bulb, digital electronic or power-

stealing thermostats.

• Refer to Electrical Wiring for thermostat, chilled water

valve and optional hot water valve wiring connections

to CAW unit along with thermostat manufacturer's

instructions for wiring and special operation or

programming. See page 17.

1. Cooling Only Thermostat Selection

Select a thermostat compatible with chilled water cooling

system and chilled water valve selected. Thermostat should

have “R”, “Y” and “G” terminals. Thermostat may also have

“C” terminal.

2. Cooling with Electric or Hot Water Heat

Thermostat Selection

Select thermostat compatible with chilled water cooling and

hot water or electric heating system with water valve(s)

selected. Thermostat should have “R”, “Y”, “W” and “G”

terminals. Thermostat may also have “C” terminal.

Sequence of Operation Wall Mounted

Thermostat

Follow all installation and electrical wiring instructions

prior to applying power to the unit. If CAW unit is

equipped option heating, either electric or hot water, verify

thermostat is set to energize the fan with call for heating.

1. Fan Operation

Some thermostats are equipped with AUTO/ON fan switch.

Placing switch ON will run the fan continuous. Placing

switch in AUTO position will cycle the fan with call for

heating or cooling through the “R” and “G” low volt terminal

connections.

After thermostat is satisfied and call for heat or cooling is

removed or the fan switch is set to auto the indoor fan will

remain on for sixty (60) seconds to purge remaining energy

from unit thereby increasing efficiency.

2. Cooling Operation

A. Apply power to unit and place system switch in

“COOL” mode. Adjust set-point temperature below

room temperature. Chilled water valve will open

and fan motor(s) will energize.

B. Place set-point temperature above room

temperature. Chilled water valve will close and fan

remains on for additional sixty seconds.

2. Cooling with Electric Heat or Hot Water Heat

Operation

Set thermostat Configuration for cooling/electric

heat operation. Follow thermostat manufacturer's

instructions for configuration settings.

B. Apply power to the unit and place system switch in

“HEAT” mode. Adjust set-point temperature above

room temperature. Electric heat will energize or

hot water valve will open and fan motor(s) will

energize.

C. Place set-point temperature below room

temperature. Electric heat will switch off or hot

water valve will close and fan remains on for

additional sixty seconds.

Содержание Ductless Series









































Результаты поиска

Содержание Ductless Series

Отзывы:

Похожие инструкции для Ductless Series

Бренды по названию

Популярные бренды

ECR International Ductless Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Ductless Series

Отзывы:

Похожие инструкции для Ductless Series

Бренды по названию

Популярные бренды