EcoWater ETF AIIF115 страница 11 Скачать руководство пользователя

Страница: 11 / 24

Installation

ECOWATER

S Y S T E

M S

9. PRESSURE TESTING FOR LEAKS

TO PREVENT EXCESSIVE AIR PRESSURE IN

THE FILTER AND PLUMBING SYSTEM, DO THE

FOLLOWING STEPS IN ORDER

Open two or more filtered water faucets, both hot

and cold.

Referring to Figure 8, turn the bypass valves to

service position.

Slowly open the main water supply valve.

Close the filtered water faucets after both of the

following occur.

-- water runs smoothly, with no air bubbles

-- you can smell the sanitizing (page 6) bleach odor

at the faucets

Check your complete installation for leaks. If re-

work is required, be sure to observe precautions in

step 6.

10. CONNECT ALL LEADWIRES

Connect the wire harness to the valve switch and

to the timer, Figure 9. The switch is on the valve, by

the large gear. Snap the sensor onto the outport of

the valve.

NOTE:

Check to be sure the connector is secure on

the back of the timer.

Attach the connector, on the valve motor leadwire,

to the the matching connector on the faceplate timer.

Connect the power cable leads to the back of the

timer.

Connect the leads from the relay box to the back

of the timer. Secure the wire using the strain relief

and attaching it to the valve.

11. CONNECT AIR PUMP

On the floor or a shelf nearby the filter, fasten the

air pump in place.

Install the air filter (if required) and tubing connec-

tor fitting.

Connect the tubing from the check valve, on the

adaptor, to the connector fitting on the air pump.

Plug the pump into the relay box connector.

12. CONNECT TO ELECTRICAL POWER

Plug both the transformer and relay box into continu-

ously “live”, grounded, 115V--60Hz house electrical

outlets, approved by local codes.

13.

TO COMPLETE INSTALLATION, DO THE PRO-

GRAMMING STEPS ON PAGES 12 AND 13.

NOTE: WATER HEATER START--UP ON PAGE 13.

24V

BACK OF TIMER

POSITION

SWITCH

24VAC

TRANSFORMER

FIGURE 9

GND

OUT

TURBINE

SENSOR

RELAY BOX

TO 115V

OUTLET

CONNECT TO

AIR PUMP

Содержание ETF AIIF115

























Результаты поиска

Содержание ETF AIIF115

Отзывы:

Похожие инструкции для ETF AIIF115

Бренды по названию

Популярные бренды

EcoWater ETF AIIF115, Руководство пользователя

Результаты поиска

Содержание ETF AIIF115

Отзывы:

Похожие инструкции для ETF AIIF115

Бренды по названию

Популярные бренды