EcoWater CHC Series страница 4 Скачать руководство пользователя

Страница: 4 / 130

5.3.1

Gauge Problems-................................................................................................................51

5.3.2

Low Pump (s) Pressures- ...................................................................................................51

5.3.3

High Pump Pressures-........................................................................................................52

5.3.4

Differential pressure too High or too Low- .......................................................................52

5.3.5

Filter Back Wash Failures- ................................................................................................52

5.4

Frequent pump seal Failures- ....................................................................................................59

5.5

Issues with Actuators and Solenoids-........................................................................................60

5.5.1

Actuator Failure- ................................................................................................................60

5.5.2

Actuator Leaks-..................................................................................................................60

5.5.3

Non- Functional Solenoid Valves-.....................................................................................61

5.6

Issues with Conductivity Controllers-.......................................................................................62

5.6.1

Probe Cleaning and Calibration-........................................................................................62

5.6.2

Bleed Set Point- .................................................................................................................62

5.6.3

Dead Band Control- ...........................................................................................................62

5.6.4

Walchem- ...........................................................................................................................63

5.6.5

LMI-...................................................................................................................................64

5.6.6

CHC Control Station- ........................................................................................................64

5.7

CHC Control Station Messages- ...............................................................................................65

5.7.1

No Filter Backwash (BW Failure shown on Control Panel’s screen)- .............................65

5.7.2

Screen Cleaning Required Message- .................................................................................65

5.7.3

Control Panel Message of “Power OFF”-..........................................................................66

5.7.4

Control Panel Message of “Pressure LO”- ........................................................................66

5.7.5

Control Panel Message of “Power Failure”-......................................................................66

5.7.6

Control Panel Message of “Conductivity HI”- ..................................................................66

5.7.7

Control Panel Message of “Conductivity LO”- .................................................................67

5.8

Leaks- ........................................................................................................................................68

5.8.1

O-Ring Leaks or Failure- ...................................................................................................68

5.8.2

Flange gasket Leaks-..........................................................................................................68

5.8.3

Plumbing Leaks or Failure- ...............................................................................................68

5.8.4

Valve Leaks or Failure- .....................................................................................................68

5.8.5

Internal Valve Leaks-.........................................................................................................68

5.8.6

Vacuum Leaks- ..................................................................................................................68

5.9

Algae and Biofilms- ..................................................................................................................69

5.9.1

Algae growing in tower in sunlit areas-.............................................................................69

5.9.2

Biofilms- ............................................................................................................................69

5.10

Scale- .....................................................................................................................................70

Содержание CHC Series



































































































































Результаты поиска

Содержание CHC Series

Отзывы:

Похожие инструкции для CHC Series

Бренды по названию

Популярные бренды

EcoWater CHC Series, Руководство по обслуживанию и устранению неисправностей

Результаты поиска

Содержание CHC Series

Отзывы:

Похожие инструкции для CHC Series

Бренды по названию

Популярные бренды