EcoWater CHC Series страница 110 Скачать руководство пользователя | Manualshive

Страница: 110 / 130

background image

110

Screens

There are several screens that can be used within the Control Station this section looks at all of the
possible screens, their hierarchy and display and control options for each screen.
From each screen several Fkeys have been constructed to allow operational, and screen changed
function. All screens have been designed to utilize soft keys (buttons on LCD) as well as the hard keys
(Fkeys) to control the features and actions of the system.

All Return to Main keys (

Ma in

), change the screen being shown back to the Main User Screen.

All screens except the Alarm Screen automatically will revert to the Main User Screen. The time it
requires for each screen is shown in the screen flow hierarchy as shown within this manual.
There are two basic types of screens that can be accessed by the Control Station software, there are
USER screens as well as SET UP or SYSTEM screens. All SET UP and SYSTEM screens are
protected by passwords and EcoWater CHC recommends that the user is only made aware of those
passwords that are appropriate to them. That means that if the customer is a Full Service Agreement
(FSA) customer they should only be made aware of the pass words for resetting the User Defaults and
that NOTHING MORE. However if the customer has purchased the CHC Treatment system, we are
allowed to pass on the required information to the customer about all possible passwords. Please refer
these customer’s to EcoWater CHC Service so that the appropriate documentation can be given to
them.
Anyone can view and change the settings of the User Screens as desired. The user screen language will
reflect that language chosen in the Set UP Screens. The Set UP and SYSTEM screens will always be
shown in English no matter what language is chosen in the Set Up Screens.
The following pages discuss the screens in more detail:

«
...
108
109
110
111
112
...
»

Содержание CHC Series



































































































































Отзывы:

Нет отзывов

Похожие инструкции для CHC Series

Univerge SV8100

Бренд: NEC Страницы: 2

Univerge SV8100

Бренд: NEC Страницы: 14

Бренд: Harman Kardon Страницы: 2

MaestroKitchen 100

Бренд: Harman Kardon Страницы: 36

Бренд: jablotron Страницы: 30

Бренд: JBL Страницы: 2

Simply Cinema ESC333

Бренд: JBL Страницы: 16

Project K2.S5500

Бренд: JBL Страницы: 2

Бренд: JBL Страницы: 8

Бренд: Panasonic Страницы: 2

Бренд: JBL Страницы: 2

Authentics L 16

Бренд: JBL Страницы: 11

Бренд: Parkside Страницы: 201

Бренд: Parrot Products Страницы: 8

Бренд: Watchguard Страницы: 8

Naviels UKDAX-10EDT

Бренд: DAXOM Страницы: 28

Бренд: Sanden Страницы: 32

Бренд: Watts Premier Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды