EcoWater CHC Series страница 107 Скачать руководство пользователя | Manualshive

Страница: 107 / 130

background image

107

Control Station Description

The Control Station has been designed to monitor and control the CHC treatment system. It utilizes a
PLC (Programmable Logic Controller) that has been programmed by EcoWater CHC to meet the
operational requirements. Its screen layout has been designed to minimize the need for customer
interaction as well as minimize confusion in screen function and layout. There are User Screens as
well as Set Up screens. The Set Up screens will be configured at the time of installation and do not
require configuration by the user, for this reason, the Set Up screens are Password protected. The
control station is integrated into the system as shown in this diagram:

F 1

F2

F 3

F4

CHC Power Switch (Optional)

CHC Phase and Overload (Optional)

CHC Pressure Switch (Optional)

CHC Vacuum Switch Optional

Filter Power Switch

Filter Phase and Overload (Optional)

Filter Pressure Switch (Optional)

Filter Back Wash Control

Filter Alarm Monitoring

Conductivity using
Toroidal Conductivity Probe

Blow Down Actuator

Communications Options (RS232, RS485,
Ethernet, Phone Modem, Cell Modem,
Modbus)

Micro SD Memory Card

Alarm Indicator

Alarm Tracking

PLC Basic Specifications

The Control Station operates on 24 Volt DC Power
The Input signals are required to be 20-24 Volt DC
The Outputs utilize relay contacts and can handle up to 120V, 2A power control for each
The display is a monochromatic 3 ½” LCD that is direct sunlight readable.
The operational temperature range for the product exceeds our CHC system specifications.
PLC Make- Horner APG XLT, model number- XE-XT102AB. (

www.heapg.com

)

Refer to the Electrical Schematic for wiring specifications.
There are several Communication Options, refer to EcoWater CHC Service Department for more
information.

Mounting

The Control Station must be mounted in an appropriately rated enclosure. This enclosure could include
a motor starter box or could be enclosed in a separate box to the side. The front panel is rated for
Nema 4X (IP65) use. Please refer to the PLC’s Manual for further specifications.

«
...
105
106
107
108
109
...
»

Содержание CHC Series



































































































































Отзывы:

Нет отзывов

Похожие инструкции для CHC Series

Бренд: Water Tec Страницы: 20

Бренд: R.V.R. Elettronica Страницы: 38

Бренд: Galletti Страницы: 8

Бренд: Nacon Страницы: 12

Бренд: 4rain Страницы: 44

S15 Non-Metallic

Бренд: Sandpiper Страницы: 25

Бренд: Samsung Wisenet Страницы: 16

Бренд: Zamel Страницы: 12

Бренд: Zamel Страницы: 12

Бренд: Panasonic Страницы: 2

Aerco AM Series

Бренд: Watts Страницы: 7

Бренд: Danfoss Страницы: 22

Бренд: Calpeda Страницы: 72

LEADER ECOTRONIC Series

Бренд: DAB PUMPS Страницы: 10

Бренд: JBL Страницы: 6

Бренд: ICON Страницы: 16

Бренд: Polk Mono Страницы: 86

Бренд: Neptune Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды