ECOVACS Winbot 7 series, Инструкция по эксплуатации

Страница: 3 / 60

Quick User Guide
1. PREPARATON BEFORE USE
Important notes to help you get a quick start.
3. IMPORTANT SAFETY PRECAUTIONS
1. Be sure to place the Winbot horizontally on the window and that it is at least 4 inches from the lower corners of the window.
2. The
Safety Pod MUST be used when cleaning the outside of a window above ground level. Please read the instructions for Safety Pod use in this
Instruction Manual.
3. To safely remove the Winbot, grasp the handle of the unit and move the switch under the handle to the OFF position (far left). While still grasping the
unit, insert finger into the Air Release Trigger and pull up on it. Remove the unit from the window when the suction has diminished.
4. The Winbot may NOT be used outside while raining, snowing or colder than 40 º F or hotter than 114 º F, as it will damage the product and could
cause electrical problems.
.
.
.
.
O
F
F
O
N
≥
4 inches
●
Assemble the supply cord connector to the Power Adapter, tightening
the nut so the connector will not pull apart, then plug the Power Adapter
into your electrical receptacle. Place the Winbot’s switch button, located
under the handle, to the CHARGE position (far right) and charge the
Back Up Battery for 2 hours. The flashing Indicator Light will change to a
steady GREEN when charging is complete.
2. USE OF PRODUCT
For best results, please read the entire contents of this Instruction Manual. It provides complete and detailed information on safety, use, and maintenance
of your
Ecovacs Winbot.
ON OFF
●
While the unit is charging, take time to read the Instruction Manual for the proper and safe use of the unit.
●
Should you be cleaning the outside of a window above ground level, you must use the Safety Pod
.
Read the instructions on Safety Pod use in this
Instruction Manual.
●
●
Turn the Winbot unit over to attach the Cleaning Pads. Attach the large Cleaning Pad to the front floating plate,
making sure to cover the entire plate. Attach the small Cleaning Pad to the small area provided at the rear of
the unit. Make sure the Rear Cleaning Pad is placed exactly within its velcro area. Take care not to
cover any part of the Cupule (suction ring), or the plate that holds it, with the Rear Cleaning Pad.
NOTE: Cleaning Pads are removable and machine washable.
Immediately prior to placing the Winbot onto the window, take the glass Cleaning Solution bottle and spray
ONLY the FRONT Cleaning Pad. The pad should be slightly damp, not wet.
●
●
●
●
●
Grasp the Winbot by the handle and move the switch under the handle to the ON position (Center).
Place the Winbot horizontally on the window, making sure it is at least 4 inches from the lower corners of the window frame. There will be a slight noise.
This is the vacuum motor creating suction to hold the Winbot to the window. When the indicator light turns BLUE, Winbot has attached itself to the
window and the handle can be released.
After ensuring the Winbot is correctly placed on the glass, press the “Start/Pause” button on the Remote Control or press the “Start/Pause”
button directly on the Winbot unit. The product will use automatic cleaning mode to measure and clean the window. When Winbot is finished cleaning,
it will return to its start position, the Indicator Light will flash BLUE and the unit will emit a song to indicate the end of the cleaning cycle.
To pause Winbot during the cleaning cycle, press the “Start/Pause” button on the Remote Control or press the “Start/Pause” button directly on the
Winbot unit. The product will then pause and go into stand-by mode. To restart the cleaning process
,
press the “Start/Pause” again on the Remote
Control or directly on the Winbot unit.
When the Winbot is done cleaning remove it from the window. Grasp the handle of the unit and move the switch under the handle to the OFF position
(far left). While still grasping the unit, insert finger into the Air Release Trigger and pull up on it. Remove the unit from the window after suction has
Winbot is NOT intended to replace heavy duty or first time cleaning, this must be done manually as you have done in the past. Winbot is intended for maintenance
cleaning on standard windows.
WINBOT on that particular window until a WINBOT Extension Cord is attached (Extension Cord sold separately).
2. Loop one end of the Safety Rope around the Safety Pod's channel and pull it tight.
3. Loop the other end of the Safety Rope to the nut on the power cord and tighten. (If an Extension Cord is attached the Safety Rope should still be tied to the nut on the power
cord.)
Note: Do NOT attach the Safety Rope to the thin part of the cord.
4. Press the Safety Pod suction cup FIRMLY on the inside, lower corner of the window. Make sure the Safety Pod suction cup is securely in place.
5. Place WINBOT on the window, close the window, and start WINBOT.
6. After WINBOT is done cleaning remove it from the window. Grasp the handle, switch the unit OFF, insert finger into Air Release Trigger and pull up on it for 20 seconds until
suction has diminished.
1. Make sure that there is enough power cord for the WINBOT to clean the entire window without restricting its movement. If there is not enough cord, it is not safe to use the
Warning
If Winbot is used to clean an outside window above ground level, the Safety Pod MUST be used.
Winbot must be used in strict accordance with the directions in the Instruction Manual. Ecovacs Robotics, Inc. can not be held liable or
responsible for any damages or injuries caused due to improper use.
EN