Ecosys M6526cdn Type B Скачать руководство пользователя страница 176

Страница: 176 / 206

Troubleshooting

8-2

Indicators During Sending/Receiving Operation

The

Processing

and

Memory

indicators show the fax

transmission status.

• The

Processing

indicator blinks when the machine

is sending/receiving a fax.

• The

Memory

indicator blinks when source data is

being stored in memory for memory transmission.

• The

Memory

indicator is lit when there is source

data stored in the memory for delayed
transmission.

Responding to an ATTENTION Indicator Flashes

If an

ATTENTION

indicator flashes, press [Status/Job Cancel] to check an error message. If the message is not

indicated on the Message Display when [Status/Job Cancel] is pressed or the

ATTENTION

indicator flashes,

check the following.

Symptom

Checkpoints

Corrective Actions

Reference Page

Cannot send fax.

Is the modular cord
connected correctly?

Connect the modular
cord correctly.

—

Is Permitted FAX No. or
Permitted ID No.
registered correctly?

Check Permitted FAX
No. and Permitted ID
No..

6-30

Has a communication
error occurred?

Check error codes in the
TX/RX Result Report
and Activity Report. If
the error code starts with
"U" or "E", perform the
corresponding
procedure.

Appendix-12

Is the destination FAX
line busy?

Send again.

—

Does the destination
FAX machine respond?

Send again.

—

Is there an error other
than above?

Contact your Service
Representative.

—

Содержание M6526cdn Type B















































































































































































































Результаты поиска

Содержание M6526cdn Type B

Отзывы:

Похожие инструкции для M6526cdn Type B

Бренды по названию

Популярные бренды

Ecosys M6526cdn Type B, Руководство по эксплуатации

Результаты поиска

Содержание M6526cdn Type B

Отзывы:

Похожие инструкции для M6526cdn Type B

Бренды по названию

Популярные бренды