Ecosys M6526cdn Type B Скачать руководство пользователя страница 194

Страница: 194 / 206

Appendix-12

Error Code List

When a transmission error occurs, one of the following error codes is recorded in the TX/RX Result Report and
Activity Report.

NOTE:

If an error occurs during V34 communication, the

in the error codes is replaced by an

Error Code

Possible Cause/Action

Busy

Failed to establish connection with the recipient
despite auto redialing the preset number of times.
Send again.

CANCELED

Transmission was canceled due to an action to
cancel transmission.
Reception was canceled due to an action to
cancel reception.

U00300

Paper depletion occurred at the recipient
machine. Check with the recipient.

U00430 - U00462

Reception was canceled because of mismatching
of communication features with the sender
machine although the line connection was
established.

U00601 - U00690

Communication was stopped due to the machine
failure. Send or receive again.

U00700

Communication was stopped due to failure on the
part of the sender or recipient machine.

U00800 - U00811

Page(s) not sent correctly. Send again.

U00900 - U00910

Page(s) not received correctly. Ask the sender to
resend.

U01000 - U01097

Communication error occurred during
transmission. Send again.

U01100 - U01196

Communication error occurred during reception.
Ask the sender to resend.

U01400

Failed to establish communication with the sender
or recipient machine because dialing registered
for a push line system was used in a pulse line
system.

U01500

Communication error occurred during high-speed
transmission. Send again.

U01600

Communication error occurred during reception of
high-speed transmission. Ask the sender to
reduce the transmission speed and send again.

Содержание M6526cdn Type B















































































































































































































Результаты поиска

Содержание M6526cdn Type B

Отзывы:

Похожие инструкции для M6526cdn Type B

Бренды по названию

Популярные бренды

Ecosys M6526cdn Type B, Руководство по эксплуатации

Результаты поиска

Содержание M6526cdn Type B

Отзывы:

Похожие инструкции для M6526cdn Type B

Бренды по названию

Популярные бренды