Ecolibrium Solar EcoFoot5D Скачать руководство пользователя страница 17

Страница: 17 / 19

EcoFoot5D Install Guide V1.1-FINAL

Page 17 of 19

January 25, 2018, ES10560

ecolibriumsolar.com

Step 4 – Install Hardware on Bases

4.1

Install Elevator Bolts and Nut Coupling into EcoFoot 5D bases. Torque to 8 ft-lb.
Repeat process on both Bases.

Step 5 – Install Ballast Tray and secure to Mid-Span Support & Bases

5.1

Referring to Step 5 of the Installation Guide, install Ballast Tray. Line up slots with attachment stud,
base hardware and Mid-Support.

5.2

Torque fastener into Mid-Span Support to 14 ft-lbs. through slot on Ballast-Tray.

5.3

Fasten Ballast Tray to base with Washers and Serrated Hex Bolts on both bases.
Torque to 8 ft-lb.

5.4

Install Washer and Serrated-Flange Nut onto Preferred Roof Attachment in order shown below.
Torque Serrated -Flange Nut to 14 ft-lbs.

5.5

Roof Attachment installation complete for Seismic Rated Attachment System.

Nut Coupling
and Elevator Bolts

Washers and
Serrated Hex
Bolts

Washer and
Serrated Hex Nut

Serrated
Hex Bolt

Содержание EcoFoot5D




















Результаты поиска

Содержание EcoFoot5D

Отзывы:

Похожие инструкции для EcoFoot5D

Бренды по названию

Популярные бренды

Ecolibrium Solar EcoFoot5D, Руководство по установке

Результаты поиска

Содержание EcoFoot5D

Отзывы:

Похожие инструкции для EcoFoot5D

Бренды по названию

Популярные бренды