Eco-King HWB-299, Инструкция по установке и обслуживанию

Страница: 89 / 124

E93.1801EN171 HWB installation manual 89
Lock-
out
code Error Description Cause Solving
16 FLUE_GAS_
ERROR Flue temperature ex-
ceeded the maximum
flue temperature There is no water in
the heat exchanger or
flue gas sensor is mal-
functioning or heat ex-
changer is overheated. Check if flue sensor is work-
ing correctly if not so replace
flue sensor. Check waterflow
if to low increase waterflow.
17 STACK_ER-
ROR Internal software error wrongly programmed
BCU or PB reset BCU or replace BCU
and or display unit
18 INSTRUC-
TION_ ERROR Internal software error wrongly programmed
BCU or PB reset BCU or replace BCU
and or display unit
19 ION_CHECK_
FAILED Internal software error wrongly programmed
BCU or PB reset BCU or replace BCU
and or display unit
20 FLAME_OUT_
TOO_LATE Flame still present 10
seconds after closing
the gas valve wrong earthing of BCU
and boiler Check earthing of BCU and
boiler
21 FLAME_BE-
FORE_IGNIT Flame is detected be-
fore ignition wrong earthing of BCU
and boiler Check earthing of BCU and
boiler
22 TOO_MANY_
FLAME_LOSS Three time flame lost
during 1 demand bad gas supply or CO2
level is not correct or
bad ignition rod check gas supply pressure,
check CO2 level and adjust if
necessary, replace ignition
rod or replace ignition cable.
23 CORRUPTED_
ERROR_NR Error code RAM byte
was corrupted to an un-
known error code. wrongly programmed
BCU or PB reset BCU or replace BCU
and or display unit
27 FILLING_TOO_
MUCH Too many automated
filling attempts in a short
time period If output is pro-
grammed as filing
valve and there are too
many filing attempts Check if there is a leak in the
central heating system or if
the boiler itself is leaking also
check expansion vessel on
internal leak
28 FILL_TIME_
ERROR Filling takes too long If output is pro-
grammed as filing
valve and filling takes
more than 10 minutes Check if there is a leak in the
central heating system or if
the boiler itself is leaking also
check expansion vessel on
internal leak
29 PSM_ERROR Internal software error wrongly programmed
BCU or PB reset BCU or replace BCU
and or display unit
30 REGISTER_
ERROR Internal software error wrongly programmed
BCU or PB reset BCU or replace BCU
and or display unit
32 T_EX-
CHANGE_
DIFF_ERROR The 2 exchange sensors
deviate too much for
more than 60 seconds There is not enough
water flow through the
heat exchanger Check if the general pump is
running and if all valves are
open to make enough flow
33 LWCO_1_
ERROR Low water cut off 1 error There is no water in
the heat exchanger or
not electrically con-
nected Check if there is enough wa-
ter in the heat exchanger if
not so fill up the system
34 LWCO_2_
ERROR Low water cut off 2 error There is no water in
the heat exchanger or
not electrically con-
nected Check if there is enough wa-
ter in the heat exchanger if
not so fill up the system
35 APS_NOT_CL
OSED_IN_POS
T_PURGE Air pressure switch not
closing during post-
purge 1 no air transport to the
burner after heat de-
mand; flue or air inlet
is blocked, or APS is
jammed or air signal
hose not connected to
the air intake pipe or
water in hose Check if there are any ob-
structions in the flue or air in-
take, replace APS if jammed,
connect air hose to the air in-
take pipe, remove any water
from the hose.
36 GAS_PRES-
SURE_ERROR Gas pressure switch
open for more than
E2_GPS_Timeout wrong gas pressure on
gas supply Check if gas pressure is in
limits of the gas pressure
switch.