ECM egrCAN Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 52

ECM egrCAN Скачать руководство пользователя страница 34

30

Appendix B: Module Stand-alone Mode and EIB Mode

CAN data from LambdaCAN and NOxCAN(g) modules can either be taken directly from the

modules themselves or from the CAN port of display heads connected to the modules. When

data is taken directly from one or more modules, each module must in Stand-alone mode.

When data is taken from one or more display heads of an EGR 5210, Lambda 5220, or EGR

5230 analyzer, each module must be in EIB mode.

Therefore, the module must be properly configured in Stand-alone mode or EIB mode

depending on how it will be used. When LambdaCAN and NOxCAN(g) modules are sold

alone, they are delivered in Stand-alone mode. When LambdaCAN and NOxCAN(g)

modules are sold as part of a NOx 5210, Lambda 5220, or EGR 5230 analyzer, they are

delivered in EIB mode.

To convert from one mode to the other requires software reprogramming of the module

followed by the installation (to set to Stand-alone) or removal (to set to EIB) of a jumper

inside the module.

To convert a module from EIB to Stand-alone Mode

1. Take the nut off the end of the module. Use an 18mm socket without the wrench.

2.

Release the two tangs at each side of the module.

«
...
32
33
34
35
36
...
»

Содержание egrCAN





















































Отзывы:

Нет отзывов