ECM egrCAN Скачать руководство пользователя страница 27

Страница: 27 / 52

Setup Option Level 1

Function

MOd

Select module s/n. Default is NONE.

RATE

Set parameter averaging rate. Range 0.001 to 1.000

Default is 1.000

dISP

Select parameter. Note: Parameters available are

those programmed using Configuration Software.
CONF LEdS

Set display intensity. Default is 3333.

LOCK

Lock and Unlock Display for Programming

MOd, RATE, and dISP appear on the upper display for the upper channel and on the lower

display for the lower channel. CONF just appears on the lower display and is for global

dashCAN setup. All entries must be followed by pressing the ENT key.
Table 6: Menu Tree for dashCAN

MOd (Module) Setup Option

In MOd setup, the serial number of the module assigned to the upper or lower channel is

entered. The serial number is written on a label on the module. The module assigned to the

upper channel will send information to the upper display and the module assigned to the

lower channel will send information to the lower display. The same module can be assigned

to both channels or different modules can be assigned to each channel.

After entering MOd (i.e. press ENT when “MOd” is displayed), the serial numbers of the

available modules will be displayed. Select using

↑

and

↓

followed by the ENT key.

RATE Setup Option

Data is transmitted from modules at the broadcast rate and the programmed averaging that

was programmed using the Configuration Software. This transmitted data can then be

further averaged before being displayed on the displays. Separate averaging can be

programmed for the upper display and the lower display.

The averaging is programmed with values from 0.001 (heavy averaging) to 1.000 (no

averaging). The default is 1.000. The averaging is performed as follows:

DisplayedValue

x Parameter

+ (1 –

) x DisplayedValue

t-1

where:

DisplayedValue

= the new displayed value

= The user-programmable averaging.

Range: 0.001 (heavy averaging) to 1.000 (no averaging).

Parameter

= the latest value transmitted by the module

DisplayedValue

t-1

= the previous displayed value

The selected display averaging does not affect the module’s CAN transmission rate or

averaging.

Содержание egrCAN





















































Результаты поиска

Содержание egrCAN

Отзывы:

ECM egrCAN, Инструкция по эксплуатации, Страница: 27 / 52

Результаты поиска

Содержание egrCAN

Отзывы: