ECM egrCAN Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 52

ECM egrCAN Скачать руководство пользователя страница 30

26

gasoline: 1.70 < H:C < 2.10, O:C=0.0, N:C=0.0, (1.75 or 1.85 are commonly used)
methanol: H:C=4.0, O:C=1.0, N:C=0.0
ethanol: H:C=3.0, O:C=0.5, N:C=0.0
propane: H:C=2.67, O:C=0.0, N:C=0.0
methane: H:C=4.0, O:C=0.0, N:C=0.0

Maximum allowable levels of fuel "Impurities":

Lead: 0.012 gm/gal., 0.003 gm/ltr.
Phosphorous: 0.0008 gm/gal., 0.00027 gm/ltr.
Sulfur: 0.035% by weight

Do not use the O

2

sensor in a heavily-sooting or crankcase-oil-burning engine

because these conditions will shorten the life of the sensor.

Thread Size: 18mm x 1.5 mm. Lightly coat with non-lead containing antiseize

compound. The O

2

sensor's thread size is identical to that of the

exhaust gas oxygen (EGO) sensors used in current production

automobiles with 3-way exhaust catalysts.

Hex Size: 22 mm

Tightening Torque: 40

±

4 Nm, 30

±

3 ft-lbf for exhaust O

2

,

4

±

1 Nm, 3

±

1 ft-lbf for intake O

2

Pressure Sensor

Note: Must attach to engine via pressure sensor tubing only!

Do not directly attach to the engine or pressure sensor damage will result.

Diaphragm Material: Stainless steel

Maximum Pressure: 200 Psia, 1379 kPa (absolute)

Operating Temperature Range: -40 to 105 °C

Thread on Pressure Sensor: ¼” NPT

Fitting on Pressure Sensor: Swagelok SS-400-7-4 to mate with ¼” tube (USA) or

Swagelok SS-6MO-7-4 to mate with 6 mm tube (Metric)

Pressure Sensor Tubing

Note: Stainless steel end of tubing towards engine. Teflon end towards pressure sensor.

«
...
28
29
30
31
32
...
»

Содержание egrCAN





















































Отзывы:

Нет отзывов