P0016-LI-02.01
33
No Type & Description
02-
20
Zone 02 - 20 Alarm
As Zone 01 Alarm.
Group 40: Zone Tamper
The tamper condition of each zone can be assigned to an output:
No Type & Description
01 Zone
01
Tamper
This output type activates when zone 01 generates a tamper
alarm and deactivates when the alarm is reset.
02-
20
Zone 02 - 20 Tamper
As Zone 01 Tamper.
Group 50: Zone Masked
The mask condition of each zone can be assigned to an output:
No Type & Description
01 Zone
01
Masked
This output type activates when zone 01 generates a mask fault
and deactivates when the fault is cleared and reset.
02-
20
Zone 02 - 20 Masked
As Zone 01 Masked.
Group 60: Zone Fault
The fault condition of each zone can be assigned to an output:
No Type & Description
01 Zone
01
Fault
This output type activates when zone 01 generates a fault and
deactivates when the fault is cleared and reset.
02-
20
Zone 02 - 20 Fault
As Zone 01 Fault.
Group 70: Zone Bypassed
The bypass condition of each zone can be assigned to an output:
No Type & Description
01
Zone 01 Bypassed
This output type activates when zone 01 is bypassed and
deactivates when the zone is reinstated.
02-
20
Zone 02 - 20 Bypassed
As Zone 01 Bypassed.
Group 80: User Access
The system access of each user can be assigned to an output:
No Type & Description
00
User 00 Access
This output type activates for 30 seconds after user 00 has
entered their access code.
01-
10
User 01 - 10 Access
As User 00 Access.
Communication Ports
These two options allow the operating mode for the two on-board
communication ports to be configured.
Locations:
6201
- Com Port 1: Mode.
6202
- Com Port 2: Mode.
Entry Mode:
Selection List (see page 16).
0 UDL
USB-Link
This mode configures the selected communication port for UDL
USB-Link operation. The USB-Link should be connected to the
computer and the other end should be connected to the selected
control panel communication port.
1 Printer
This mode configures the selected communication port for printer
operation. Use this mode when using a terminal program via the
USB-Link to capture the printer output from the control panel.
2 3
rd
Party Module
This mode configures the selected communication port for a 3
rd
Party Module operation. Use this mode when connecting a
supported 3
rd
party communication module to the control panel.
3 Communication
Module
This mode configures the selected communication port for
Communication Module operation. Use this mode when
connecting any Eclipse communication module to the control
panel.
4 Contact
ID
This mode configures the selected communication port for
Contact ID operation. In this mode the Contact ID in ASCII format
is sent to the port.
5 Debug
USB-Link
This mode configures the selected communication port for data
debug operation. Use this mode when using a terminal program
via the USB-Link to capture the debug data from the control
panel.
GSM & SMS Centre
These options allow the GSM and SMS Centre to be configured.
Locations:
6301
- GPRS APN Name
6302
- GPRS APN User
6303
- GPRS APN Password
6304
- SIM Pin
6302
- SIM Credit Code
6311
- SMS Service Centre
Entry Mode:
String Edit - Number Mode (see page 18).
GPRS APN Name
The Access Point Name (APN) used by the GSM network operator
for IP packet data communication.
GPRS APN User
The APN user name used to log into the APN.
GPRS APN Password
The APN password name used to log into the APN.
Listed below are the GPRS setting used by the major UK GSM
network operators:
Operator APN User
Password
Vodafone internet
web
web
Orange Orangeinternet
*
*
O2 Mobile.o2.co.uk web
web
T-Mobile General.t-mobile.uk *
*
Three 3internet
* *
* = Leave blank.
SIM Pin
If the SIM is protected by a PIN, then the number must be entered
in this location in order for correct operation.
SIM Credit Code
If the GSM network operator supports credit balance via USSD,
then enter the USSD code, e.g., *123#.
