Eckman CS015 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 16

Eckman CS015 Скачать руководство пользователя страница 9

8

6. Fill with chain oil before use. Always check oil level before use. A full tank of oil
will last approximately 30 minutes. (

See Figure 2)

Pole Saw Information

SAW CHAIN TENSION

WARNING:Unplug chain saw from power source before adjusting saw chain
tension. Severe injury or death could occur from body contact with moving
chain.

WARNING: Cutting edges on chain are sharp. Use protective gloves when
handling chain.

WARNING: When cleaning saw body:-
• do not submerge saw in any liquids
• do not use products that contain ammonia, chlorine, or abrasives
• do not use chlorinated cleaning solvents, carbon tetrachloride, kerosene, or
gasoline

(Note: The saw chain tension is properly set at the factory. A new chain will stretch.
Check new chain tension frequently (after disconnecting

the plug from the power

source) during the first 2 hours of operation. Allow chain to cool down. Follow steps
below to check saw chain tension.)
1. Unplug chain saw from power source.
2. Place chain saw on a firm surface to check chain tension.
3. Pull chain with light force 1/8" away from bottom of guide bar and release (

See

Figure 3

). If chain lightly snaps back into place, tension is correct. A slight sag (1/16"

or less) between chain and bottom of guide bar is acceptable.

Figure 3

Saw Chain Tension Adjustment

1. Loosen guide bar screw before adjusting chain. (

See Figure 4

)

«
...
7
8
9
10
11
...
»

Содержание CS015

















Отзывы:

Нет отзывов