manualshive.com logo in svg

Echo SC-2013, Руководство оператора

Поделиться
Скачать
Echo SC-2013 Скачать руководство пользователя страница 27

22

3 INCH CHIPPER/SHREDDER

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSES

REMEDY

Cannot engage belt

Improper belt installation, belt not under belt 
guide

Install belt properly, install belt under belt 
guide

Improper belt tension

$GMXVWEHOWWHQVLRQ5HSODFHEHOWRUEHOW

tension spring if needed

Excessive belt wear

Not using correct belt

Contact your nearest authorized dealer to 
order the correct belt for your chipper

Pulley(s) damaged or worn

Replace pulley(s)

Pulley(s) not in alignment

Align pulley(s) to within 1/16" with straight 
edge

Belt(s) tension too loose

Replace belt or belt tension spring

Hard to feed chipper, 
requires excessive 
power to chip

Dull chipper blades

Flip, sharpen, or replace

Obstructed discharge

8VHEUDQFKRUVLPLODUREMHFWWRFOHDU

discharge tube

Improper blade clearance

Set blade/anvil clearance to recommended 
distance

Excessive vibration 
while running

Dull chipper blades

Flip, sharpen, or replace

Drive system vibration

Check drive belts, bearings, and pulleys for 
bad or worn areas. Check for dull chipper 
blades.

Rotor out of balance

Inspect rotor for damaged or missing 
chipper blades, replace if needed

Chipper blade to anvil clearance is incorrect

Set blade/anvil clearance to recommended 
distance

Содержание SC-2013



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды