manualshive.com logo in svg

Echo SC-2013, Руководство оператора

Поделиться
Скачать
Echo SC-2013 Скачать руководство пользователя страница 22

17

3 INCH CHIPPER/SHREDDER

SERVICE & MAINTENANCE

WARNING

BEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, 

AND MAKE SURE ALL MOVING PARTS HAVE COME TO A COMPLETE STOP.

4.  Using a rubber mallet tap the end of the rotor shaft to 

obtain 1/16" to no greater than 1/8" clearance. Rotate 
the rotor and check the clearance on all chipping 
blades.

5.  Once clearance has been set, the lock collars must 

be replaced and retightened. Using a punch and a 
hammer, tap the lock collars in the direction of shaft 
rotation 

(clockwise on the engine side bearing and 

counterclockwise on the chute side bearing)

 and 

set them with a hammer tap. Tighten the lock collar 
set screws.

6.  Loosen the set screws holding the belt pulley on the 

rotor shaft. Move the pulley on the shaft so it is aligned 
with the engine drive pulley. The pulley should be 
moved the same amount the rotor was moved, only 
in the opposite direction. Torque pulley set screw to 
160 in-lbs.

7.  Insure the pulley drive key is completely seated under 

the pulley and tighten the set screws.

8.  Check pulley alignment by laying a straightedge 

across the pulley faces. Pulley faces should line up. 
If not, repeat steps 6 and 7 until the pulley is lined up.

Feeding too large or too much material at once may plug 
the chipper. To clear a plugged rotor, proceed as follows:

1. 

6KXWRႇHQJLQHDQGDOORZDOOPRYLQJSDUWVWRFRPHWR

a complete stop.

2. 

5HPRYH WKH  î  FDUULDJH EROW DQG ÀDQJH

nut securing the discharge screen to the frame and 
remove the shredder screen.

3.  Clean the debris away from the chipper rotor. Turn 

the rotor by hand to be sure it is free to rotate. Be 
careful to avoid the chipper blades when cleaning out 
the debris.

4.  Install discharge screen and retaining hardware.

5.10 CLEARING A PLUGGED ROTOR

There are several optional discharge screens available 

LQ GLႇHUHQW VL]HV VHH 6HFWLRQ  2SWLRQDO GLVFKDUJH
VFUHHQV SURGXFH GLႇHUHQW VL]HG FKLSV 7R FKDQJH WKH

discharge screen, proceed as follows:

1. 

6KXW PDFKLQH Rႇ PDNH VXUH DOO PRYLQJ SDUWV KDYH

completely stopped and disconnect spark plug wire.

2.  Lift discharge door/shield to gain access to the 

discharge screen.

3. 

5HPRYHWKHîFDUULDJHEROWDQGÀDQJH

nut (2)securing the discharge screen to the frame 
(Figure 5.8). Pull discharge screen out from the 
bottom and rotate the top downward to remove.

4.  Clean any trash or debris out from the screen area.

5.  Insert the top of the replacement screen into the slot 

in the chipper body and push the bottom of the screen 
inward so bolt holes align.

6.  Install the bolt through the screen and down through 

WKHIUDPHDWWDFKÀDQJHQXWDQGWLJKWHQVHFXUHO\

5.11 CHANGING THE DISCHARGE 
SCREEN

0DNH VXUH WKH WRS ÀDQJH RI WKH GLVFKDUJH VFUHHQ LV

properly and completely installed into upper slot of the 
housing. Failing to do so may cause knives to make 
contact with discharge screen during operation.

NOTE

1

2

Figure 5.8, Changing the Discharge Screen

*Model Shown SC-2013

ENGLISH

Содержание SC-2013



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды