manualshive.com logo in svg

Echo SC-2013, Руководство оператора

Поделиться
Скачать
Echo SC-2013 Скачать руководство пользователя страница 12

7

3 INCH CHIPPER/SHREDDER

ASSEMBLY

2.2 ADD OIL TO ENGINE

Gasoline and diesel fuels are highly 

ÀDPPDEOH DQG WKHLU YDSRUV DUH
H[SORVLYH7RSUHYHQWSHUVRQDOLQMXU\RU

property damage:
Store fuel only in approved containers, 
in well ventilated, unoccupied buildings, 

DZD\IURPVSDUNVRUÀDPHV$FRQWDLQHU

with a capacity of 2 gallons or less with 
a pouring spout is recommended. Do 

QRW¿OOWKHIXHOWDQNZKLOHWKHHQJLQHLVKRWRUUXQQLQJ

since spilled fuel could ignite if it comes in contact 
with hot parts or sparks from ignition. Do not start the 
engine near spilled fuel. Never use fuel as a cleaning 
agent.

DO NOT MIX OIL WITH FUEL.

WARNING

Use only those types of fuels that are recommended in 
your engine owner’s manual.

To add fuel:

&KHFNWKHRLOOHYHODQGLIQHHGHG¿OOWKHHQJLQHFUDQNFDVH
ZLWK WKH W\SH DQG DPRXQW RI RLO VSHFL¿HG LQ WKH HQJLQH

owner’s manual.

2.3 FILL THE FUEL TANK

1.  Stop engine, wait for all parts to stop moving and 

disconnect spark plug wire. Remove key from key 

VZLWFK $OORZ WKH HQJLQH DQG PXႉHU WR FRRO IRU DW

least three minutes.

2. 

&OHDQDUHDDURXQGIXHO¿OOFDSDQGUHPRYHFDS

3. 

8VLQJDFOHDQIXQQHO¿OOIXHOWDQNWREHORZERWWRP
RI¿OOHUQHFNWRSURYLGHVSDFHIRUDQ\IXHOH[SDQVLRQ
,QVWDOO IXHO ¿OO FDS VHFXUHO\ DQG ZLSH XS DQ\ VSLOOHG

gasoline.

ENGLISH

Содержание SC-2013



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды