manualshive.com logo in svg

Echo SC-2013, Руководство оператора

Поделиться
Скачать
Echo SC-2013 Скачать руководство пользователя страница 24

19

3 INCH CHIPPER/SHREDDER

SERVICE & MAINTENANCE

WARNING

BEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, 

AND MAKE SURE ALL MOVING PARTS HAVE COME TO A COMPLETE STOP.

5.13 DRIVE BELTS

1

2

3

4

5

6

Figure 5.11

&KHFNWKHFRQGLWLRQRIWKHGULYHEHOWDQQXDOO\RUDIWHUHYHU\KRXUVRIRSHUDWLQJZKLFKHYHUFRPHV¿UVW,IWKHEHOWLV
FUDFNHGIUD\HGRUZRUQUHSODFHLW7RUHSODFHRUDGMXVWGULYHEHOWSURFHHGDVIROORZV

1.  Remove the belt shield, upper belt guide (6) and lower belt guard (5).

2.  Remove idler pulley (2).

3. 

6OLSWKHGULYHEHOWRႇWKHEHOWSXOOH\V

4.  Inspect pulleys for wear. Replace the pulleys 

if they are cracked or worn so that the belt 

FRQWDFWDUHDLVQRWVPRRWKDQGÀDW

5.  Place the new belt over pulleys. Do not force 

or pry the belt over pulleys as this may cause 
cord breakage. 

6.  Reinstall the idler pulley, ensuring that the belt 

is on the outside edge of the idler pulley.

7.  Check all pulleys to make sure they are 

properly aligned.

8.  Replace all shields, guides and guards.

1.  Remove discharge door/shield, discharge screen and rotor shaft end cap on chute side of the machine.

2.  Loosen the set screws on the lock collar securing the chute side bearing on the rotor shaft. 

3.  Using a punch and hammer, tap the lock collar in the opposite direction of normal rotation until loose; remove lock 

collar and bearing.

4.  Remove the upper shield, upper belt guide and lower belt guard to allow access to the engine side bearing.

5.  Remove the drive belt.

6.  Loosen the set screws holding the belt pulley on the rotor shaft and remove the pulley. 

7.  Repeat steps 2 and 3 on the engine side rotor bearing.

8.  Remove the bolts securing the chipper chute cover to the frame and remove chipper chute cover.

9. Remove 

rotor.

5.14 REMOVING THE ROTOR

ENGLISH

Содержание SC-2013



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды