manualshive.com logo in svg

Echo Power Blend TC-210, Руководство оператора

Поделиться
Скачать
Echo Power Blend TC-210 Скачать руководство пользователя страница 33

X7504083609

33

© 4/2016 ECHO Inc.

TC-210

MAINTENANCE

Gear Housing

1.

Remove tines (See Tine Removal/
Cleaning - Installation below).

2.

Remove gear case cover (A). Be 
careful not to tear sealing gasket 
(C).

3.

Support tiller with exposed gear 
case (D) upward. Add grease until 
nearly level with top of gear case 
(D).

Do not over fill.

 Too much grease will cause pressure and possible seal 

failure.

Tine Removal/Cleaning - Installation

Note:  Always wear gloves to protect hands from sharp blades.

Stop engine and disconnect spark plug wire before removing or 
installing tines. Contact with revolving tines will cause severe 
injury.

1.

Remove retaining pin (E) and slide tine from shaft.

2.

Remove weeds, etc. from tines and wash dirt from unit.

3.

Clean accumulated dirt and debris form 
gear housing and tine shaft.

4.

Select "Tilling" or "Cultivating" position, 
and install tines facing forward (tilling) 
or rearward (cultivating).

A

D

C

B

E

Содержание Power Blend TC-210













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды