Echo Power Blend TC-210 Скачать руководство пользователя страница 19

Страница: 19 / 44

X7504083609

TC-210

OPERATION

Two Stroke Oil

- A two-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738)

and J.A.S.O. FD Standards must be used. Echo brand premium Power Blend
X

™

Universal 2-Stroke Oil meets these standards. Engine problems due to

inadequate lubrication caused by failure to use an ISO-L-EGD (ISO/CD 13738)
and J.A.S.O. M345-FD certified oil, such as Echo premium Power Blend X

™

will void the two-stroke engine warranty.

Echo premium Power Blend X

™

Universal 2-Stroke Oil may be mixed at

50:1 ratio for application in all Echo engines sold in the past regardless
of ratio specified in those manuals.

Handling Fuel

Fuel is VERY flammable. Use extreme care when mixing, storing or
handling, or serious personal injury may result.

◆

Use an approved fuel container.

◆

DO NOT smoke near fuel.

◆

DO NOT allow flames or sparks near fuel.

◆

Fuel tanks/cans may be under pressure. Always loosen fuel
caps slowly allowing pressure to equalize.

◆

NEVER refuel a unit when the engine is HOT or RUNNING!

◆

DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks
outdoors over bare ground.

◆

DO NOT overfill fuel tank. Wipe up spills immediately.

◆

Securely tighten fuel tank cap and close fuel container after
refueling.

◆

Inspect for fuel leakage. If fuel leakage is found, do not start or
operate unit until leakage is repaired.

◆

Move at least 3 m (10 ft.) from refueling location before
starting the engine.

Mixing Instructions

Fill an approved fuel container
with half of the required amount of
gasoline.

Add the proper amount of 2-stroke
oil to gasoline.

Close container and shake to mix
oil with gasoline.

Add remaining gasoline, close fuel
container, and remix.

Fuel to Oil Mix – 50:1 Ratio

Metric

Gas

Oil

Gas

Oil

Gallons

Oz.

Liter

CC.

2.6

100

5.2

200

500

Содержание Power Blend TC-210













































Результаты поиска

Содержание Power Blend TC-210

Отзывы:

Бренды по названию

Популярные бренды

Echo Power Blend TC-210, Руководство оператора

Результаты поиска

Содержание Power Blend TC-210

Отзывы:

Бренды по названию

Популярные бренды