manualshive.com logo in svg

Echo Power Blend TC-210, Руководство оператора

Поделиться
Скачать
Echo Power Blend TC-210 Скачать руководство пользователя страница 26

MAINTENANCE

TC-210

26

X7504083609

© 4/2016 ECHO Inc.

IMPORTANT NOTE

 - Time intervals shown are maximum. Actual use and your 

experience will determine the frequency of required maintenance.
* Replacement is recommended based on the finding of damage or wear during 
inspection

MAINTENANCE PROCEDURE NOTES:

(1) Apply lithium based grease every 25 hours of use.

(2) Low evaporative fuel tanks DO NOT require regular maintenance to maintain 
emission integrity.

Air Filter

Level 1.

1.

Close choke (Cold Start Position 

[

]). This prevents dirt from 

entering the carburetor throat when 
the air filter is removed. Brush 
accumulated dirt from air cleaner 
area.

2.

Remove air filter cover. Brush dirt 
from inside cover.

3.

Remove air filter and lightly brush 
debris from filter. Replace filter if it is damaged, fuel soaked, very dirty, or 
the rubber 
sealing edges are deformed.

Air Filter 

Replace*

1

Fuel Filter 

Inspect*

1

Fuel Cap Gasket 

Inspect*

1

Spark Plug 

Inspect/Clean/Replace*

1

Muffler Spark Arrestor 

Inspect/Clean/Replace* 

2

Cylinder Exhaust Port 

Inspect/Clean/Decarbon 

2

Gear Housing

Grease(1)

2

Yearly

Fuel Filter 

Inspect/Replace*

1

Fuel Cap Gasket 

Replace* 

1

Parts Required:

REPOWER

TM

 AIR & FUEL FILTER KIT.

COMPONENT/SYSTEM

MAINTENANCE 

PROCEDURE

REQ’D 

SKILL 

LEVEL

Содержание Power Blend TC-210













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды