background image

6

PRODUCT  EMIssION  DURAbILITy  (EMIssION COMPLIANCE PERIOD)

The 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emis-

sions output meets applicable emissions regulations, provided that approved maintenance procedures are followed as 

listed in the Maintenance Section of this manual.

Emission Control Label 

  (located on Engine)  (EXAMPLE ONLY, information on label varies by FAMILY).

equIpment

 

check

  WARNING  

Use only ECHO approved attachments. Serious injury may result from the use of a non-approved attachment combi

-

nation. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have 

not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and safety 

manual.

•  Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed.                                         

                                         

•  Check that the cutting attachment is firmly attached and in safe operating condition.

  

 WARNING

Moving parts can amputate fingers or cause severe injuries.  Keep hands, clothing and loose objects away from all 

openings.     

• 

ALWAys

 stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop  

before removing obstructions, clearing debris, or servicing unit.

• 

DO NOT

 start or operate unit unless all guards and protective covers are properly assembled to unit.

• 

NEVER

 reach into any opening while the engine is running.  Moving parts may not be visible through openings.

  WARNING

Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or leaks are found, 

do not use unit, otherwise serious personal injury or property damage may occur. Have unit repaired by an autho-

rized servicing dealer before using.

e

mIssIon

 c

ontrol

  (

exhaust

 

&

 

evaporatIve

)

EPA 2010 and Later 

The emission control system for the engine is EM/TWC (Engine Modification and 3-way Catalyst) and for the fuel tank 

the Control System is EVAP (Evaporative Emissions) or N (for nylon tank). Evaporative emission may be applicable to 

California models only.

Содержание HC-225

































Отзывы: