background image

H

edge

 C

lipper

5

O

peratOr

'

s

 M

anual

 

  

  DANGER

Do not operate this product indoors or in inadequately ventilated 

areas. Engine exhaust contains poisonous emissions and can cause 

serious injury or death.

Read the Manuals

•  Provide all users of this equipment with the Operator’s Manual and 

Safety Manual for instructions on Safe Operation.

Clear the Work Area

•  Spectators and fellow workers must be warned, and children and 

animals prevented from coming nearer than 15 m (50 ft.) while the 

unit is in use.

Keep a Firm Grip

•  Always hold the throttle handle and support handle with thumbs and 

fingers encircling the handles. 

Keep a Solid Stance

•  Maintain footing and balance at all times. Do not stand on slippery, 

uneven or unstable surfaces. Do not work in odd positions or on lad-

ders. Do not over reach.

Avoid Hot Surfaces

•  Keep exhaust area clear of flammable debris. Avoid contact during 

and immediately after operation.

  

 WARNING 

Never perform blade maintenance procedures while engine is run-

ning.

Repetitive Stress Injuries 

It is believed that overusing the muscles and tendons of the fingers, hands, arms, and shoulders may cause soreness, 

swelling, numbness, weakness, and extreme pain in those areas.  Certain repetitive hand activities may put you at a high 

risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which 

could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged 

exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.  

To reduce the risk of RSI/CTS, do the following:  

•  Avoid using your wrist in a bent, extended, or twisted position. 

Instead try to maintain a straight wrist position. Also, when grasping, 

use your whole hand, not just the thumb and index finger.                         

•  Take periodic breaks to minimize repetition and rest your hands.  

•  Reduce the speed and force with which you do the repetitive move

-

ment.  

•  Do exercise to strengthen the hand and arm muscles. 

•  Immediately stop using all power equipment and consult a doctor if 

you feel tingling, numbness, or pain in the fingers, hands, wrists, or 

arms. The sooner RSI/CTS is diagnosed, the more likely permanent 

nerve and muscle damage can be prevented.

Содержание HC-225

































Отзывы: