Echo CS-550P Скачать руководство пользователя

Страница: 24 / 36

CS-550P

CHAIN AND GUIDE BAR COMBINATION

The following combinations are recommended for model

CS-550P

GUIDE BAR

(Low-kickback)

Replacement guide bars.
The following guide bars may be considered to
have equivalent kickback energy.
• Sprocket nose guide bars of the same length

and nose radius, same pitch and having the
same number of teeth.

• Hard nose guide bars of the same length and

nose radius as a sprocket nose bar.

SAW CHAIN

(Low-kickback)

CAUTION

Do not use replacement saw chain unless it
has been designated as meeting the ANSI
B175.1 - 2000 kickback performance
requirements, when tested on the
representative sample of chain saws below
3.8 c.i.d. specified in ANSI B175.1 - 2000.

NOTE

LOW KICKBACK SAW CHAIN meets the
kickback performance requirements of ANSI
B175.1 - 2000 (safety requirements for gasoline-
powered chain saws).

Guide Bar

Saw chain

Length mm (in)

Part No.

Pitch mm (in)

Part No.

Links

Double Guard

406 (16)

16F0LD3366

8.26 (0.325)

20LPX66CQ, 20BPX66CQ

16F0LD3859

9.53 (3/8)

72LPX59CQ, 72LGX59CQ

457 (18)

18F0LD3372

8.26 (0.325)

20LPX72CQ, 20BPX72CQ

18F0LD3864

9.53 (3/8)

72LPX64CQ, 72LGX64CQ

508 (20)

20F0LD3378

8.26 (0.325)

20LPX78CQ, 20BPX78CQ

20F0PD3870

9.53 (3/8)

72LPX70CQ, 72LGX70CQ

Before using the 9.53 mm (3/8 in.) pitch bar and chain, ask your authorized ECHO dealer to change the
rim sprocket.

Содержание CS-550P





































Результаты поиска

Содержание CS-550P

Отзывы:

Похожие инструкции для CS-550P

Бренды по названию

Популярные бренды

Echo CS-550P, Инструкция по эксплуатации

Результаты поиска

Содержание CS-550P

Отзывы:

Похожие инструкции для CS-550P

Бренды по названию

Популярные бренды