Echo CS-550P Скачать руководство пользователя

Страница: 23 / 36

CS-550P

End of the guide bar

may be placed at the

height of about 40 cm (16 in.).

40 cm
(16 in.)

Rear handle

should be gripped lightly with the

right hand.

AUTOMATIC CHAIN BRAKE

Kickback produced from the tip of the guide bar will
trip the automatic chain brake. To make sure that
the automatic chain brake operates properly, follow
these steps:

1. Stop the engine.

2. Hold the saw with the guide bar approximately

40 cm (16 in.) above a wooden surface. Right
hand should hold the rear handle, and left hand
should hold the front handle.

3. Release the front handle and drop the end of the

guide bar against the wooden surface.

4. The impact should lock the chain brake.

IMPORTANT

When checking the operation of the automatic
chain brake, use a soft surface substance like
wood to provide the impact so the chain is not
damaged.

WINTER OPERATION

Use the air shutter to prevent carburetor trouble in
winter.
• Remove air cleaner cover. Pull the air shutter to

cold position.

NOTE

For operation at normal temperature, return the
air shutter to its original place. (5°C, 41°F)
It causes over heating of the engine.

Air shutter

Air cleaner cover

Cold weather position

(pull; opend)

Warm weather position

(push; closed)

Содержание CS-550P





































Результаты поиска

Содержание CS-550P

Отзывы:

Похожие инструкции для CS-550P

Бренды по названию

Популярные бренды

Echo CS-550P, Инструкция по эксплуатации

Результаты поиска

Содержание CS-550P

Отзывы:

Похожие инструкции для CS-550P

Бренды по названию

Популярные бренды