Echo CS-550P страница 12 Скачать руководство пользователя | Manualshive

Страница: 12 / 36

background image

10

CS-550P

PREPARATION FOR USE

WARNING

Saw chain is sharp! Always wear gloves
when handling assembly, otherwise serious
personal injury may result.

GUIDE BAR AND SAW CHAIN
INSTALLATION/REMOVAL

1. Remove spark plug lead. (See page 25)

2. Remove two clutch cover nuts and remove clutch

cover.

3. Remove bar and saw chain if necessary. See

“Maintenance and Care” section for guide bar/
saw chain maintenance procedures.

4. Unlock the chain brake, and mount guide bar on

studs and slide toward clutch to make saw chain
installation easier. Install chain with cutters on
top of guide bar facing foward.

5. Install the clutch cover over the guide bar studs.

Ensure chain tension adjuster pin fits into the
guide bar adjuster hole. Tighten clutch cover nuts
finger tight.

Spiked bumper

Clutch cover

Brake lever
(Front hand guard)

Two nuts

Clutch

Nuts

Guide bar adjuster hole

Clutch cover

Guide bar studs

Unlock chain brake

«
...
10
11
12
13
14
...
»

Содержание CS-550P





































Отзывы:

Нет отзывов

Похожие инструкции для CS-550P

Бренд: YATO Страницы: 96

Бренд: Tanaka Страницы: 28

Fatmax SFMCCSB664

Бренд: Stanley Страницы: 192

Бренд: Homelite Страницы: 449

Бренд: Echo Страницы: 65

Бренд: Poulan Pro Страницы: 57

Бренд: Poulan Pro Страницы: 9

Бренд: Racing Страницы: 17

Бренд: Poulan Pro Страницы: 18

Бренд: North American Tool Страницы: 23

Бренд: Oregon Scientific Страницы: 92

Бренд: Tanaka Страницы: 37

Бренд: AL-KO Страницы: 192

Бренд: Stihl Страницы: 32

Бренд: Makita Страницы: 10

Бренд: Echo Страницы: 5

Бренд: Husqvarna Страницы: 30

Бренд: PowerBase Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды