background image

OPERATION

CS-4510

32

X7503350603

© 06/2019 ECHO Incorporated.

Note:  Do not increase engine speed while chain brake is locked. 

Severe brake damage will result.

Running

The saw chain should not move at idle, otherwise serious 
personal injury may result.

Note:  If saw chain moves adjust carburetor according to 

“Carburetor Adjustment” instructions in this manual, or see 
your dealer.

1.

After engine starts, allow it to return to 
idle and warm up before using.

2.

Move chain brake lever fully 
REARWARD to UNLOCK chain brake.

3.

Squeeze throttle trigger gradually and 
increase engine speed.

4.

The chain starts running when the 
engine reaches clutch engagement 
speed (see technical data page).

5.

Confirm proper acceleration and 
lubrication of chain and bar.

6.

Do not run the engine at high speed unnecessarily.

7.

Be sure that saw chain stops moving when throttle trigger is released.

Stopping

1.

Release throttle trigger and allow engine to idle.

2.

Push the momentary stop switch until the engine is stopped.

Note:  If engine does not stop, pull choke control knob out fully to 

stop engine. 

Note:  Return the unit to your authorized dealer to check and repair 

stop switch before starting the engine again.

Shown with optional
Kick Guard

TM

Unlock Chain brake

Содержание CS-4510

























































Отзывы: