Echo CS-355T Скачать руководство пользователя страница 8

8

CS-355T

OPERATOR SAFETY

ViBraTiOn anD COLD

•  It is believed that a condition called Raynaud’s Phe-

nomenon, which affects the fingers of certain individu

-

als, may be brought about by exposure to vibration 

and cold. Exposure to vibration and cold may cause 

tingling and burning followed by loss of color and 

numbness in the fingers. The following precautions 

are strongly recommended because the minimum 

exposure which might trigger the ailment is unknown. 

•  Keep your body warm, especially the head and neck, 

feet and ankles and hands and wrists. 

•  Maintain good blood circulation by performing vigor-

ous arm exercises during frequent work breaks and 

also by not smoking. 

•  Limit the number of hours of operation. Try to fill each 

day with jobs where operating the chain saw, or other 

hand-held power equipment is not required. 

•  If you experience discomfort redness and swelling of 

the fingers, followed by whitening and loss of feeling, 

consult your physician before further exposing your-

self to cold and vibration.

rEPETiTiVE STrESS inJUrY 

•  It is believed that over-using the muscles and ten-

dons of the finger, hands, arms and shoulders may 

cause soreness, swelling, numbness, weakness and 

extreme pain to the areas just mentioned. Certain 

repetitive hand activities may put you at a high risk for 

developing a repetitive stress injury (RSI).

•  An extreme RSI condition is Carpal Tunnel Syndrome 

(CTS) which could occur when your wrist swells and 

squeezes a vital nerve that runs through the area. 

Some believe that prolonged exposure to vibration 

may contribute to CTS. CTS can cause severe pain 

for months or even years. 

 To reduce the risk of RSI/CTS, do the following:

•  Avoid using your wrist in a bent, extended or twisted 

position. 

•  Take periodic breaks to minimize repetition and rest 

your hands. 

•  Reduce the speed and force in which you do the 

repetitive movement. 

•  Do exercises to strengthen hand and arm muscles.

•  See a doctor if you feel tingling, numbness or pain in 

your fingers, hands, wrists or arms. The sooner RSI/

CTS is diagnosed, the more likely permanent nerve 

and muscle damage can be prevented.

EYE anD HEaring PrOTECTiOn

•  Wear eye protection goggles that meet ANSI Z 87.1 

requirements. Goggles meeting the requirements 

have the mark “Z 87” stamped on them.

•  Wear hearing protection. If this guideline is not fol-

lowed, hearing loss can occur. ECHO recommends 

wearing hearing protection at all times. 

wEar PrOPEr CLOTHing

•  Snug fitting durable clothing should be worn. Pants 

should have long legs, do not wear shorts. Do not 

wear loose fitting clothing, scarves, neckties, jewelry 

or any item that may become tangled in surrounding 

growth or the chain saw itself.

•  Wear shoes with non-skid soles. Do not wear open 

toed shoes or operate unit barefooted.

•  Wear no-slip, heavy duty work gloves to improve your 

grip on the chain saw handles. The gloves also help 

reduce the transmission of machine vibration to your 

hands.

•  Keep long hair away from engine and air intake. Re-

tain hair with cap or net.

HOT HUMiD wEaTHEr

•  Heavy protective clothing can increase operator fa-

tigue which may lead to heat stroke. Schedule heavy 

work for early morning, or late afternoon hours when 

temperatures are cooler.

aVOiD HOT SUrFaCES

•  During operation, the muffler or catalytic muffler and 

surrounding cover become hot.

•  Never suspend the saw on a lanyard with the engine 

running.

•  Always use the saw from the right-hand side of your 

body - 

never

 from the left side.

•  Always wear proper safety clothing to protect your 

lower body from sharp saw chain and hot muffler.

•  Always keep exhaust area clear of flammable debris 

during transportation or when storing, otherwise seri-

ous property damage or personal injury may result.

  

 warning    

The ignition components of this machine generate an electromagnetic field during operation which may interfere 

with some pacemakers. To reduce the risk of serious or fatal injury, persons with pacemakers should consult 

with their physician and the pacemaker manufacturer before operating this machine. In the absence of such 

information, ECHO does not recommend the use of ECHO products by anyone who has a pacemaker.

Содержание CS-355T





































Отзывы: