background image

32

CS-355T

stOrage aFter use

      warning

Do not store in an enclosure where fuel fumes may 

accumulate or reach an open flame or spark.

      CaUTiOn

Do not lend or rent your chain saw without the 

Instruction manual and Safety manual.

nOTE

• For future reference, you should keep this 

Instruction manual and the Safety manual.

• If this Instruction manual or the Safety manual 

has become illegible or is lost, 

see “Additional Or 

Replacement Manuals” on back page for ordering 

information.

•  Inspect and adjust every part of the chain saw. 

-  Completely clean every part and repair if necessary.

-  Apply thin coating of oil on metal parts to prevent 

rust.

•  Remove chain and guide bar. 

•  Drain fuel tank completely. Press purge bulb 6 - 7 times 

to remove remaining fuel from carburetor then drain the 

tank again. Close choke, start and run the engine until 

it stops due to lack of fuel.

•  Allow engine to cool then remove the spark plug and 

pour 7 cc (1/4 oz.) of fresh, clean, two-stroke engine oil 

into the cylinder through the spark plug hole. 

•  Store in a dry area, free from dust. 

Содержание CS-355T





































Отзывы: