Echo CS-355T Скачать руководство пользователя

Страница: 6 / 36

CS-355T

End of the guide bar

may be placed at the

height of about 55 cm (22 in.).

55 cm

(22 in.)

AUTOMATIC CHAIN BRAKE

Kickback produced from the tip of the guide bar will

trip the automatic chain brake. To make sure that

the automatic chain brake operates properly, follow

these steps:
1.

Stop the engine.

2. Hold the saw with the guide bar approximately

55 cm (22 in.) above a wooden surface. Right

hand should hold the rear handle, and left hand

should hold the front handle.

3. Release the front handle and drop the end of the

guide bar against the wooden surface.

4. The impact should lock the chain brake.

IMPORTANT

When checking the operation of the automatic

chain brake, use a soft surface substance like

wood to provide the impact so the chain is not

damaged.

Rear handle

should be gripped lightly with the

right hand.

1. Do not operate a chain saw with one hand! Serious

injury to the operator, helpers, bystanders, or any
combination of these persons may result from one-
handed operation. A chain saw is intended for two-
handed use.

2. Do not operate a chain saw when you are fatigued.

3. Use safety footwear, snug-fitting clothing and

protective gloves. Wear eye, hearing, and head
protection devices.

4. Use caution when handling fuel. Move the chain saw

at least 3 m (10 feet) from the fueling point before
starting the engine.

5. Do not allow other persons to be near the chain saw

when starting or cutting with the chain saw. Keep
bystanders and animals out of the work area.

Other Safety Precautions

6. Do not start cutting until you have a clear work area,

secure footing, and a planned retreat path from the
falling tree.

7. Keep all parts of your body away from the saw chain

when the engine is running.

8. Before you start the engine, make sure that the saw

chain is not contacting anything.

9. Carry the chain saw with the engine stopped, the

guide bar and saw chain to the rear, and the muffler

away from your body. When carrying a chain saw
with the engine running, push the front hand guard
forward to engage the chain brake.

10. Do not operate a chain saw that is damaged,

improperly adjusted, or not completely and securely
assembled. Be sure that the saw chain stops moving
when the throttle control trigger is released.

11. Shut off the engine before setting the chain saw

down.

Содержание CS-355T





































Результаты поиска

Содержание CS-355T

Отзывы:

Похожие инструкции для CS-355T

Бренды по названию

Популярные бренды

Echo CS-355T, Инструкция по эксплуатации

Результаты поиска

Содержание CS-355T

Отзывы:

Похожие инструкции для CS-355T

Бренды по названию

Популярные бренды