Echo CS-355T Скачать руководство пользователя страница 13

Страница: 13 / 36

CS-355T

PREPARATION FOR USE

warning

Saw chain is sharp! always wear gloves when

handling assembly, otherwise serious personal

injury may result.

nOTE

The machine may be delivered with guide bar, tip

guard, and saw chain separated. Install guide bar, tip

guard, and saw chain as follows.

KiCK gUarD

TO Bar inSTrUC-

TiOnS

Tools Needed: Two 11 mm (7/16 in.) Wrenches.

For saws with Kick guard

P/n 2894901 and Sym-

metrical Low-Kick type (Double guard) guide bars.

1. Install bolt (A) in

rear

hole (B) of Kick Guard

and

through front hole (C) in guide bar.

iMPOrTanT:

Dimple (D) in Kick Guard

must engage

recess (E) in guide bar.

3. Tighten nut (F) and bolt (A) using 11 mm (7/16 in.)

wrenches until snug. Make certain Kick Guard

is flush

against guide bar.

4. Tighten nut (F) 1/8 additional turn.

5. Check to make certain Kick Guard

is tight on guide

bar.

gUiDE Bar anD Saw CHain inSTaL-

LaTiOn/rEMOVaL

nOTE

• Move the chain brake lever (Front hand guard) fully

rearward to remove or install the clutch cover to

chain saw.

• Align the brake connector of the clutch cover to the

groove on the side of the brake lever (Front hand

guard).

1. Remove spark plug cover and disconnect spark plug

lead.

2. Remove two clutch cover nuts and remove clutch

cover.

3. Remove bar and saw chain if necessary. See “Main-

tenance and Care” section for guide bar/saw chain

maintenance procedures.

(A)

(D)

(E)

(C)

(B)

(F)

Clutch cover

Brake lever

(Front hand guard)

Two nuts

Brake connector

Содержание CS-355T





































Результаты поиска

Содержание CS-355T

Отзывы:

Похожие инструкции для CS-355T

Бренды по названию

Популярные бренды

Echo CS-355T, Инструкция по эксплуатации

Результаты поиска

Содержание CS-355T

Отзывы:

Похожие инструкции для CS-355T

Бренды по названию

Популярные бренды