manualshive.com logo in svg

Echo CS-2511WES, Руководство по обслуживанию

Поделиться
Скачать
Echo CS-2511WES Скачать руководство пользователя страница 6

SERVICE INFORMATION

4

CS-2511WES

251Ws

1-2  Technical data (continued)

Carburetor adjustment

Fuel type

Mixed two-stroke 

regular fuel

Mixed two-stroke 

E10 fuel

Premixed

alkylate fuel

1) Initial setting

H mixture needle

turn out

1 3/4

2

2 1/4

L mixture needle

turn out

2 1/2

Throttle adjust screw turn in*

1

1 1/2

*

1

 Set Throttle adjust screw to the point that its tip just contacts throttle plate before initial setting.

IMPORTANT:

 Use 

Tachometer PET-1000R

 to measure engine speed (Refer to 1-6 Special tools).

IMPORTANT:

 The PI controller installed model has 2 mode; Carburetor adjustment mode and Operation 

mode. When adjusting carburetor, must be changed from Operation mode to Carburetor adjustment mode.
The mode will return to the Operation mode when the engine is stopped.

To change the mode,
1. Start engine without brake activated. 

(Do not touch throttle lever.)

2. Engine warm-up with fast idle for 120 seconds. 

(The speed should be within 6,000 - 10,000 r/min. If it 

is not, adjust the speed by turning H mixture needle.)

CAUTION: 

Chain will start to rotate during engine warm-up with fast idle.

NOTE:

 Do not stop engine during carburetor adjustment. If the engine is stopped, restart this procedure from 

the beginning.

The carburetor adjustment continues.

Engine warm-up

Idle - WOT : Total

sec.

5 - 5 : 30

2) Confirm that the mode has changed

Confirm to vary the idle engine speed by turning L 

mixture needle 1/4 turn CW. If the speed does not 
vary, change the mode again.

(The idle engine speed returns to 3,200 r/min for a 
few seconds in Operation mode, when the engine 

speed is deviated.)

3) Find idle maximum speed

Adjust L mixture needle to maximum idle speed*

2

4) Set idle maximum speed w/ TAS

r/min

4,100

5) Set idle speed by turning L mixture needle CCW r/min

3,300

6) Verify final engine speed with standard equipment

Idle: 3,100 - 3,300

WOT: 12,800 - 13,400

r/min

If the WOT speed is not within above range, 
readjust H mixture needle and reverify the speed.
If that does not work, adjust H mixture needle by 
1/8 turn and reverify the speed.

7) Verify clutch engagement speed

Confirm clutch engagement speed.

If it is less than 1.25 times the idle speed,
adjust the idle speed by turning TAS CCW.

WOT:

 Wide open throttle   

CCW:

 Counterclockwise   

TAS:

 Throttle adjust screw

*

2

 If clutch engages during adjustment process 2), decrease engine speed by turning TAS CCW until clutch 

disengages and then redo 2).

Содержание CS-2511WES

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды