manualshive.com logo in svg

Echo CS-2511WES, Руководство по обслуживанию

Поделиться
Скачать
Echo CS-2511WES Скачать руководство пользователя страница 59

ENGINE

57

CS-2511WES
251Ws

A

8-4 Testing crankcase and cylinder sealings

1. Remove air cleaner cover, air filter and carbure

-

tor from the unit (Refer to 

4-9 Testing carburetor

 ).

2.  There  are  two  ways  to  seal  intake  port  and 
crankcase pulse passage. Choose convenient one 
from followings.

Way1  :

  Install  pressure  plate  897827-16131  (A) 

and  tighten  M5  bolts  (B)  of  8-10  mm  (0.3-0.4  in) 
length.

Way2 :

 Install pressure rubber plug 897826-16131 

(C) and carburetor (D) and tighten original bolts (E) 
for carburetor.

3.  To  seal  exhaust  port  of  cylinder,  cut  pressure 
rubber plug 91041 (F) off as shown.

4. Remove exhaust plate and muffler (G) with ex

-

haust gasket (H) (Refer to 

8-3 Inspecting muffler 

and exhaust port

 ).

5. Set pressure rubber plug (F) to muffler (G) with 

exhaust gasket (H) as shown.

NOTE

  :  Make  sure  to  cover  exhaust  port  (g)  of 

muffler with pressure rubber plug (F).

6. Gently tighten muffler bolts (J1 and J2) until the 

muffler  (G)  and  pressure  rubber  plug  (F)  fit  with 

cylinder. Then turn muffler bolts (J1) 180 degrees 

clockwise.

NOTE

 : Do not install exhaust plate. Do not tighten 

muffler  (G)  and  pressure  rubber  plug  (F)  fully,  or 
muffler (G) may be deformed.

44mm

17mm

C

E

D

F

F

G

H

J1

g

J2

B

Содержание CS-2511WES

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды