manualshive.com logo in svg

Echo CS-2511WES, Руководство по обслуживанию

Поделиться
Скачать
Echo CS-2511WES Скачать руководство пользователя страница 35

FUEL SYSTEM

33

CS-2511WES
251Ws

4-8 Adjusting carburetor (continued)

4-8-3 Adjusting carburetor

PI controller installed model has 2 mode; Carburetor 
adjustment mode and Operation mode.

When  adjusting  carburetor,  must  be  changed  from 
Operation  mode  to  Carburetor  adjustment  mode  in 
the following steps.

1. Start engine without brake activated. Do not touch 
throttle lever.

2.  Warm  up  engine  with  fast  idle  for  120  seconds.
The speed should be within 6,000 - 10.000 r/min. If it 
is not, adjust the speed by turning H mixture needle.

CAUTION:

  Chain  will  start  to  rotate  during  engine 

warm-up with fast idle.

NOTE:

 Do not stop engine during carburetor adjust-

ment.  If  the  engine  is  stopped,  start  above  steps 
from the beginning.

3.  Warm up engine for 30 seconds alternating engine speed between WOT 5 seconds and idle 5 seconds. 

4. Confirm to vary the idle speed by turning L mixture needle 1/4 turn clockwise. If the speed does not 

vary, change the mode again.

NOTE:

  The  idle  engine  speed  returns  to  3,200  r/min  for  a  few  second  in  Operation  mode,  when  the 

engine speed is deviated.

5.  Adjust L mixture needle (B) using D-shaped tool (A) to reach maximum engine speed just before lean 
drop off. 

If chain starts to rotate during adjustment, decrease engine speed by turning throttle adjust screw (D) 
counterclockwise untill chain stops and then readjust L mixture needle (B).

6.  Set  idle  engine  speed  to  4,100  r/min  by  turning Throttle  adjust  screw  (D).  Engine  speed  should  be 
stable at 4,100 +/- 50 r/min after Throttle adjust screw adjustment.

7.  Turn L mixture needle (B) counterclockwise reducing engine idle speed 800 r/min to set idle speed at 
3,300 r/min. The engine idle speed ranges 3,200 - 3,400 r/min.

NOTE : 

Engine speed must be allowed to stabilize a minimum of 20 seconds after each adjustment of L 

mixture needle to assure accurate tachometer readings.

8.  Stop engine and restart engine. Verify engine idle speed ranges from 3,100 to 3,300 r/min, and WOT 
engine speed ranges from 12,800 to 13,400 r/min. If the WOT speed is not within above range, return to 
“4-8-2 Initial setting” and set H mixture needle again. If that does not work, adjust H mixture needle by 1/8 

turn. Make sure the chain does not rotate when engine is idling. When final adjustment is completed, the 
engine should idle, accelerate smoothly, and attain WOT per above specifications.

9. Confirm clutch engagement speed. If it is less than 1.25 times the idle speed, adjust the idle speed by 

turning TAS counterclockwise.

NOTE: 

WOT engine speed in field operation may vary from final adjustment specifications due to chang

-

ing ambient conditions and fuel. Safe engine speed variances should be within the WOT and Idle engine 
speed ranges listed in Section “1-2 Technical data”, otherwise the carburetor should be readjusted.

1

7

4

3

2

A

B

C

D

Содержание CS-2511WES

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды