manualshive.com logo in svg

Echo CS-2511T, Руководство владельца/оператора

Поделиться
Скачать
Echo CS-2511T Скачать руководство пользователя страница 12

12

CS-2511T

   WARNING

Saw chain is sharp! Always wear gloves 

when handling assembly, otherwise serious 

personal injury may result.

GUIDE BAR AND SAW CHAIN  

INSTALLATION/REMOVAL

NOTICE

• Move the chain brake lever (Front hand guard) 

fully rearward to remove or install the clutch 

cover to chain saw.

• Align the brake connector of the clutch cover to 

the groove on the side of the brake lever (Front 

hand guard).

1.  Remove spark plug lead. (See page 26)
2.  Loosen the clutch cover nut and remove clutch 

cover.

3.  Remove bar and saw chain if necessary. See 

“Maintenance and Care” section for guide bar/

saw chain maintenance procedures.

4.  Mount guide bar on stud and slide toward clutch 

to make saw chain installation easier. Install 

chain with cutters on top of guide bar facing  

forward.

5.  Unlock the chain brake, and install the clutch 

cover over the guide bar stud. Ensure chain  

tension adjuster pin fits into the guide bar  

adjuster hole, brake band is positioned around 

clutch drum. Tighten clutch cover nut finger tight. 

6.  Turn saw over, and check brake band for correct 

position on clutch drum. If brake band is not in 

place around drum, remove cover, make sure 

brake is unlocked, and reinstall. Tighten clutch 

cover nut finger tight. 

   WARNING

Improper clutch cover assembly can result 

in serious injury, and will cause severe 

saw damage if unit is started. Never start 

or operate saw if brake band is not in place 

on clutch drum. Always check chain brake 

operation after replacing cover. Do not 

use saw if chain brake does not function 

properly. 

Spiked bumper; option

PREPARATION FOR USE

Clutch cover

Brake lever

(Front hand guard)

A nut

Unlock chain brake

Brake connector

Guide bar 

adjuster hole

Clutch cover

Adjuster pin

Clutch

Guide bar stud

Brake connector

Содержание CS-2511T





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды