background image

4 INCH CHIPPER

1

Section

CauTIon

Indicates a potentially hazardous situation that, if not 

avoided, may result in minor or moderate injury.

DanGer

Indicates an imminently hazardous situation that, if not 

avoided, will result in death or serious injury.

warnInG

Indicates a potentially hazardous situation that, if not 

avoided, could result in death or serious injury.

1.1  saFeTY alerT sYmBol

saFeTY

1

The Owner/Operator’s manual uses this symbol to alert 

you of potential hazards.  Whenever you see this symbol, 

read and obey the safety message that follows it.  Failure 

to obey the safety message could result in personal injury, 

death or property damage.

1. 

Read  and  understand  this  owner’s  manual.  Be 

completely  familiar  with  the  controls  and  the  proper 

use of this equipment.

2.  Familiarize yourself with all of the safety and operating 

decals on this equipment and on any of its attachments 

or accessories.

3. 

Keep safety decals clean and legible.  Replace missing 

or illegible safety decals.

4. 

Obtain and wear safety glasses and 

use hearing protection at all times 

when operating this machine.

5. 

Avoid  wearing  loose  fitted  clothing.  

Never operate this machine while 

wearing clothing with drawstrings that 

could wrap around or get caught in the machine.

6. 

Do  not  operate  this  machine  if  you  are  under  the 

influence of alcohol, medications, or substances that 

can affect your vision, balance or judgement.  Do not 

operate if tired or ill.  you must be in good health to 

operate this machine safely.

7.  Do  not  operate  this  equipment  in  the  vicinity  of 

bystanders.    Keep  the  area  of  operation  clear  of  all 

persons, particularly small children.  It is recommended 

that bystanders keep at least 50 feet (15 meters) away 

from the area of operation. 

8. 

Do not allow children to operate this equipment.

9. 

use only in daylight or good artificial light.

10. Do not operate machine without shields in place.  

Failure to do so may cause serious injury or death.

11. 

Keep all guards, deflectors, and shields in good working 

condition.

12. Before inspecting or servicing any part of this machine, 

shut off the machine and make sure all moving parts 

have come to a complete stop. Disconnect the battery 

and remove the ignition key where applicable.

13. 

Check that all screws, nuts, bolts, and other fasteners 

are secured, tightened and in proper working condition 

before starting the machine.

14. Do not transport or move machine while it is operating 

or running.

1.2  BeFore operaTInG

Содержание CH5540
























Отзывы: